User Account

All Pages

How to determine the force that must be applied at a

Assignment Help Civil Engineering
Reference no: EM13305056

The uniform load has a mass of 450 and is lifted using a uniform 35- strongback beam and four ropes. Determine the Tension in the ropes Determine the force that must be applied at A.

Reference no: EM13305056

Questions Cloud

Construct the report of condition balance sheet : Construct the report of condition balance sheet for First Nation Bank for December 31 of the year just ended from the following information.
Determine maximum deflection in spring at the instant : At the instant, the system is at rest and the spring is compressed by 50mm. Determine A) Velocity of block A when the spring is unstretched B) Maximum velocity of Block B C) Maximum deflection in the spring
How could hurricane revise its invoicing policy : How could hurricane revise its invoicing policy and make its denomination decision to achieve low financing costs without excessive exposure to exchange rate fluctuations?
How could hawaii co. achieve low-cost financing : The prevailing US long-term interest rate is 9 percent versus 3 percent in japan. assume that the interest rate parity exists and tat Hawaii Co. believes that the international fisher effects holds.
How to determine the force that must be applied at a : The uniform load has a mass of 450 and is lifted using a uniform 35- strongback beam and four ropes. Determine the Tension in the ropes Determine the force that must be applied at A.
Find the volume of the nucleus : The nucleus of the hydrogen atom has a radius of about 1.1 Ã- 10-15 m. find the volume of the nucleus
Determine the interplanar spacings for the sets of planes : The atomic radius for iron has been measured to be 0.1241 nm. Determine the interplanar spacings for the (111) and (211) sets of planes
Determine the critical path-starting and finishing times : Activity Description Duration Immediate Predecessors ST Start milestone - Activity Description duration Inmdiate predesesor ST Start milestone - - A excavate st. 1 4 ST B Order & steel del. work 7 ST C Formwork st.
Compute the electron energy : Electrons are used in a single-slit diffraction experiment. Such an experiment works well if the slit has a width of 10 times the wavelength. what is the electron energy

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the angle theta as a function of delta t

At the reference temperature, three identical rods of length L form a pin jointed truss in the shape of an equilateral triangle, ABC. Determine the angle theta as a function of delta T, the temperature increase of the rod AB.

  Coefficient of static friction between pacakges

The belt starts from rest at time t=0 and its speed increases at a constant rate of 150mm/s^2. Knowing that the coefficient of static friction between the pacakges..

  Calculate the peak financial requirement

given the following cost expenditures for small warehouse answer project calculate the peak financial requirement, average overdraft.

  Radioactive waste from a clinical laboratory

A radioactive waste from a clinical laboratory contains 0.2 μCi (microcuries) of calcium-45 (45Ca) per liter. The half-life of 45Ca is 152 days.

  Calculate the elavations at vpc-vpt-high point and station

A 2000 ft vertical curve connects to a +3% grade to a -5% grade. If the vertical tangents intersect at station 52+60.55 and elevation 877.62 ft, calculate the elavations at the VPC, VPT, high point and station 54+00.

  Determining height for trajectory motion

The elastic ball bounces down a flight of rigid stairs. Determine the height h of the steps if all the trajectories between successive steps are identical. Use e = 0.85 and the initial velocity 6 m/s.neglect friction. (Theta=70 degrees)

  Estimate the min do and the critical location in river

After initial mixing, the DO concentration in the river is 9.5mg/L and the temperature is 15ºC. If the ultimate BOD of the mixed river water is 30mg/L,

  Determine what external force is required to hold the bend

A pipe 1ft in diameter bends through an angle of 135 degrees. The velocity of flow of gasoline ( S = 0.8) is 20ft/s and the pressure is 10psig in the bend. What external force is required to hold the bend against the action of the gasoline

  Uva levels in raw and treated drinking water

My question is regarding UVA levels in raw and treated drinking water with regard to TOC and DOC removal. Is there a jar test procedure that incorporates the UVA values of the various stages of treatment and is there a document you could refer me ..

  Hypothetical velocity distribution in a horizontal channel

The hypothetical velocity distribution in a horizontal, rectangular open channel is V=0.3y (m/s), where V is the velocity at a distance y (m) from the bottom of the channel. If the vertical depth of flow is 2 m and the width of the channel is 4 m,..

  Elastic modulus of steel

Given: elastic modulus of steel is 200 GPa, yield and ultimate tensile strength of steel are 600 and 750 MPa, respectively.

  Tightness of skid along with pump-motor

What is the solution if foundation bolt cut by some way from their bottom of skid, i mean skid base than how to keep another bolt etc for tightness of skid along with pump-motor already fittied with pipe and other fitting's too..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd