Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
water flows from a lake into a steep natural channel. the water surface elevation of the lake is 97.0 with respect to the datum. the channel properties are given below. determine the flow rate in the channel Hint: Construct a table of top widths, and areas. determine the critical depth by interpolation. Elevation ft 91.0 91.5 92.0 92.5 93.0 93.5 94.0 94.5 95.0 95.5 96.0 96.5 97.0 Top Width ft 0 9 15 19 18 19.5 22 27 29 31 34 37 40
Conduct either a qualitative or quantitative risk assessment on this project. Identify the risk factors that you consider most important for the suspension bridge construction. How would you assess the riskiness of the project? Why?
A vertical triangular orifice in the wall of a reservoir has a base 0.9m long,0.6m below its vertex and 1.2 m below the water surface. determine the theoretical discharge?
This material is related Geotechnical Engineering, please only answer if you are certain and sure of your answer. An undisturbed soil sample has a dry unit weight of 112 pcf with a specific gravity of solids equals to 2.68.
The center to center spacing to the two tanks is 14 m. The new tank imparts 150 kPa at the ground surface. Find the increase in vertical stresses due to the weight of the two tanks mid- way between the two tanks at the center of the clay layer.
An aluminum alloy tube of length 600mm and circular cross section with an inner diameter of 32mm and an external diameter of 36mm is subjected to an axial tensile force of 25kN. Find the change in length of the tube.
Discussion on how sustainability and green engineering can be integrated in the four components of materials science and engineering?
Link ABrotates through a limited range of angle β, and its end Acauses the slotted link ACto rotate also. For the instant represented where β= 60 and = 0.6 rad/sconstant, determine the corresponding value of r r'.
A 3000-lb car has a maximum speed (at sea level and on a level, paved surface) of 140 mi/h with 16-inch-radius wheels, a gear reduction of 3.5 to 1, and a drivetrain efficiency of 92%. It is known that at the car's top speed the engine is producin..
Normal load at failure was 93.8N with a maximum shear load of 38.7N. Find stresses on the failure plane, sketch a graph showing these on the shear stress and normal stress axes. Find the friction angle and shear strength.
The height (in meters) of a projectile shot vertically upward from a point 2 m above ground level with an initial velocity of 24.5 m/s is h2+24.5t-4.9t^2 after t seconds. a) When does the projectile reach its maximum height? b) What is the maximum..
CALCULATE THE REQUIRED DIAMETER OF STEEL TIE RODS NECESSARY TO SUPPORT A BALCONY. EACH ROD, SUSPENDED FROM A ROOF TRUSS, SUPPORTS A FLOOR AREA OF 7.0m^2. THE COMBINED BALCONT FLOOR LOAD IS 10.5 kPa
The acceleration of point A is defined by the relation a = -1.08sin kt - 1.44 cos kt, where a and t are expressed in m/s^2 and seconds, respectively, and k = 3 rad/s. knowing that x = 0.16 m and v = 0.36 m/s when t = 0
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd