How to determine free-flow travel time on the route

Assignment Help Civil Engineering
Reference no: EM13313147

Two routes connect an origin and a destination and the total trips between them is 15,000 veh/hr. Route 1 has a free flow travel time of 4 mintutes and travel time increases by 3 minutes and for each additonal 1000 vehicle in flow, and route 2 has a free flow travel time of "b" minutes and travel time increases by 3 minutes for each additional 500 vehicle in flow. If the user equilibrium flow on route 1 is 9,780 veh/hr, determine: Free-flow travel time on route 2 (i.e. "b") and Equilibrium travel times.

Reference no: EM13313147

Questions Cloud

What type of barriers to entry exists in this industry : What type of barriers to entry exists in this Industry and how did Virgin Mobile manage to enter into this industry and justify why it is beneficial for existing firms to attempt to create such barriers.
Find the initial pressure for the flask : A flask contains helium gas at 11K. The Flask is thermally isolated and the gas is allowed to escape slowly through a narrow tube until the pressure within the flask is 0,98 atm
State the structural formula of the main organic product : Write the structural formula of the main organic product of the following reaction between an alcohol (CH3OH), tosyl chloride, and then a nucleophile (CH3S-).
Explain compound interest : What are the two general criteria that must be satisfied before a company can recognize revenue? Moreover explain compound interest.
How to determine free-flow travel time on the route : Route 1 has a free flow travel time of 4 mintutes and travel time increases by 3 minutes and for each additonal 1000 vehicle in flow, and route 2 has a free flow travel time of "b" minutes and travel time increases
What is the centripetal acceleration of the hammer : An athlete whirls a 7.49 kg hammer tied to the end of a 1.3 m chain in a horizontal circle. What is the centripetal acceleration of the hammer
Prepare a research memo for auditing : Prepare a research memo for auditing
Explain the information below calculate : Given the information below calculate ?H°rxn for: C2H4(g) + 6F2(g) => 2CF4 + 4HF(g). H2(g) + F2(g) => 2HF(g) ?H° = -537 kJ C(s) + 2F2(g) => CF4(g) ?°H = -680 kJ 2C(s) + 2H2(g) => C2H4(g)
Determine effective vertical stress at depths of 8m and 12m : The water table is 7m below the surface of the sand. The saturated unit weight of the sand is 19kN/m3 and that of the clay 20kN/m3; the unit weight of the sand above the water table is 16kN/m3.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine what is the pressure in cell that can be varied

Pure n-butane is contained in a laboratory cell in which the volume can be varied. The cell is maintained at a temperature of 200°F. The volume is changed until a few drops of liquid n-butane are present. What is the pressure in the cell

  Sketch the cycle on p-v coordinates

A quality of water within a piston-cylinder assembly executes a Carnot power cycle. During isothermal expansion, the water is heated from saturated liquid at 50 bar until it is a saturated vapor. The vapor then expands adiabatically to a pressure ..

  Determine the normal depth using trial and error technique

For a trapezoidal shaped channel (n=0.014 and slope = 0.0002 with a 20-ft bottom width and side slopes of 1:1.5 (V:H), determine the normal depth using trial and error technique for a discharge of 1000 cfs.

  Volume of the lake

Suppose that the distance from the lake outlet to the withdrawal cannot be more than 20 mi. What should be the new volume of the lake?

  Estimate how long it will take before the daily maximum

Estimate the steady state PM10 concentration assuming a PM10 deposition velocity of 0.12 cm/s, prevailing wind velocity of 2.5 m/s, and a constant emission flux of PM10 0.82 mg/m2-s.

  Compute normal and critical depths in a concrete culvert

compute normal and critical depths in a concrete culvert(n=0.015)with a diameter of 36in.and a bed slope of 0.002ft/ft if the design discharge is 15cfs.is the slope steep or mild?reap for S= 0.02ft/ft.

  Allowable shearing stress

The allowable shearing stress is 15 ksi in the steel rod AB and 8 ksi in the brass rod BC. Knowing that the torque of magnitude T=10 kip * in. is applied at A, determine the required diameter of a) rod AB, b) rod BC.

  Does concentration exceed the 24-hr air quality standard

Suppose the average concentration of SO2 (SOsub2) is measured to be 400microgram/cu.m at 25degree celcius and 1 atm. Does this exceed the (24-hr) air quality standard of 0.14 ppm

  Calculate the effluent concentration from the reactor

You plan to use a tank of total volume V= 10 m3 to remove a contaminant at concentration Cin = 1 g/m3 from a waste stream with a flow rate of Q = 1 m3/h. The reaction is first order with a rate constant k1 = 0.5 h-1.

  Find what flow of water in gallons per second is required

The volume of water in a reservoir is often expressed using the unit of acre-foot. A volume of 1 acre-foot is the amount of water covering an area of 1 acre to a depth of 1 foot. Lake Mead is the largest man-made lake in the United States.

  Calculate critical crack length required to cause fracture

We know that the part has an intial crack of length 0.02 mm, and that the fracture toughness is 55 MPA(m)^1/2If the part is subject to cycle loading of 300 Mpa in tension and compression, calculate (assuming Y1.2, n = 3.4 and C = 2x10^-11 in units ..

  Calculate the steady-state pollutant concentration in lake

Conditions in the sewage pipe are Qs= 0.5 m^3/s, and Cs= 100mg/L. The pollutant is destroyed in the lake with a first-order rate constant of 0.2/d. The flow rate out of the lake is 5.0 m^3/s.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd