Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
1.Take that w1 = 890 lb/ft and w2 = 500 lb/ft. Replace the loading by an equivalent resultant force Replace the loading by an equivalent resultant force
2.How many pounds of coal must be burned to keep one 100 watt light bulb lit for one hour? Assume efficiency of the power plant is 35%, the transmission losses are 10% fo the delivered poer, and the heating value of coal is 12,000 BTU/lb
3.An open-end wrench applies the forces F to the head of a bolt to produce the moment M, where each force F is normal to the surface of which is acts. Determine the magnitude of M if F=600 lb.
A 1.20-m thick strata of sand has a void ratio of 1.81. A contractor passes a vibratory roller over this extra strata, which densifies it and reduces its void ratio to 1.23. Compute its new thickness.
For a design storm specified for an urban area in Tennessee, the depth of rainfall is 2.5 inches (6.35 cm). Initial abstraction in depressions on the pervious and impervious areas was estimated at 0.5 inches (1.27 cm). Infiltration was estimated as 1..
The dry density of a compacted sand is 1.87 Mg/m^3 and the density of the solids is 2.67 Mg/m^3. What is the water content of the material when saturated. Include a phase diagram.
A film of newtonian liquid folws down the outside surface of avertical cylinder of radius R. the flow is steady, laminar and the thickness of the film is constant.
a 110 cubic centimeter volume of clay weighs 145 g in its undisturbed state. when the clay specimen is dried it weighs 110.5g. what is the natural water content of the clay, and what is the degree of saturation Assume Gs=2.70
An engineer is required to survey a nonrectangular plot of land but is unable to measure side UT directly (see Figure 2.11). The following data are taken: RU=130.0m, RS=120.0m, ST=90.0m, angle RST= 115 degrees, and angle RUT= 100 degrees.Calculate th..
A pile resists the tension developed by three stay cables for a major tent (Membrane) Structure. Assuming no bending is desired in the pile (no resultant horizontal component), what is the magnitude of the force S if the angle \thetaS = 30 degrees
A brass alloy has a yield strength of 280 MPa, a tensile strength of 390 MPa, and an elastic modulus of 105 GPa. A cylindrical specimen of this alloy 12.7 mm in diameter and 250 mm long is stressed in tension and found to elongate 7.6 mm.
To remove the solution containing metal from a part after plating the part is commonly rinsed with water. The rinse water is contaminated with metal and must be treated before discharge. The Shiny Metal Plating Co. The plating solution contains 85..
A two story school has interior columns that are spaced 15 ft apartin two perpendicular directions. If the loading on the flat roof isestimated to be 20 lb/ft^2 determine the reduced live loadsupported by a typical interior column at
Explain how medical technologies and the pharmaceutical industry are driving healthcare service demands and costs? What are the cost/benefits of this trend?
The distance AB is measured as 322.33 ft, the angle at A is measured as 32º15' and the angle B is determined to be 41º30'. Determine the stations of the PC and PT.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd