How many bank cubic yards will be required to embankment

Assignment Help Civil Engineering
Reference no: EM13319502

You are constructing an embankment of 250,000 cubic yards of material. The material has a shrink percentage of 18%. How many bank cubic yards will be required to complete this embankment?

Reference no: EM13319502

Questions Cloud

Explain how much naoh in grams is needed to prepare solution : How much NaOH in grams is needed to prepare 546 mL of solution with a pH of 10.00? The molecular weight of NaOH is 40.0 g/mol. Hint: Since NaOH is a strong base it ionizes (disassociates) completely. The OH- concentration equals the initial concen..
Calculate the work produced and heat rejected by the engine : A completely reversible heat engine uses a solar receiver for a hightemperature reservoir and a lake for a low temperature reservoir. The sun maintains the receiver surface at 290 ° F while the lake remains at 40 °F.
The application of the concepts and techniques : Prepare an Outline for your Final Project based on your approved Project Proposal  The Outline must be structured on the Proposal to ensure the application of the concepts and techniques learnt in this module.
Show that the expenditure approach and the income approach : In a simple economy, suppose that all income is either compensation of employees or profits. Suppose also that there are no indirect taxes. Calculate gross domestic product from the following set of numbers. Show that the expenditure approach and the..
How many bank cubic yards will be required to embankment : You are constructing an embankment of 250,000 cubic yards of material. The material has a shrink percentage of 18%. How many bank cubic yards will be required to complete this embankment
Explain derive the ph henderson hasselback equation : Consider a mixture of salt NaA and weak acid HA. Please derive the pH Henderson Hasselback equation by writing the equilibrium expression. Define the pKa
Determine what is the dry weight of the material : A soil borrow material in its natural state in the ground has a unit weight of 86 pcf. Its natural water content is 9%. What is the dry weight of this material
What is the water content of this borrow material : A soil borrow material in its natural state in the ground has a unit weight of 85 pfc. When a sample of this soil is dried in the laboratory, its dry unit weight is 72 pfc.
Explain the empirical formula of the unknown compound : An unknown compound contains only C, H, and O. Combustion of 4.40 g of this compound produced 8.79 g of CO2 and 3.60 g of H2O. What is the empirical formula of the unknown compound. CHO

Reviews

Write a Review

Civil Engineering Questions & Answers

  Estimate how much carbon must be purcahsed

Estimate how much carbon (in pounds) must be purcahsed for a typical 2-bed carbon adsorption system to treat 5000 cfm of air at 95 degrees F and 1 atm. The air contains 600 ppm of styrene.

  Calculate the nominal and the effective rate of return

A 10-year, 12%, $1,000 bond that pays dividends quarterly can be purchased for $900. If the bond is purchased and pays as scheduled, calculate the nominal and the effective rate of return that the purchaser receives.

  Calculate the overall copper recovery for the process

A froth flotation process is used to concentrate copper ore. It is a two stage process with a rougher stage followed by a cleaner stage. The cleaner tailings are returned to the rougher flotation.

  Determine the maximum service load

Determine the maximum service load W (kips) at the mid-height of the beam-column shown in the accompanying figure 2.1. Assume the member is hinged with respect to bending in both x and y directions at the top and bottom.

  Determine what is the first-order decay rate constant

A minimum contact time of 30 min is required to reduce the pathogen concentration from 100 pathogens/L to below 1 pathogen/L through a first-order decay process. You plan on treating water at a rate of 1,000 gal/min.

  What will be the new exponent of the blasius equation

The relative roughness ofa pipe is 0.0005, if the blasius equation is applicable for Thecflow Reynolds number above 2700 rather then 3000

  What is rate of entropy generation assuming the surrounds

Steam expands in an turbine operating in steady-state conditions with a mass flow rate of 40,000 kg/hr. The steam enters the turbine at 8 MPa and 500 C, and exits as a saturated vapor at 40 kPa.

  Find pounds of ferric chloride per million gallons are used

a ferric chloride dosage of 40 mg/l and an equivalent dosage of lime are used to coagulate a water. (a) how many pounds of ferric chloride per million gallons are used

  Quartzite sample in a compression testing machine

A quartzite sample in a compression testing machine is 180mm long and 54mm in diameter. what is the stress under a load of 100kN? if the modulus of elasticity is 102kN/mm2, find the strain develope in the sample.

  Determine best hydraulic section for min wetted perimeter

A flume discharges 42.0 cfs on a slope of 0.50 ft in 1000 ft. The section is rectangular, and Manning's roughness coefficient is 0.012. Determine the best hydraulic section, i.e., the dimension for minimum wetted perimeter.

  How to find degree of kinematic indeterminacy

how to find degree of kinematic indeterminacy

  Shear and bending moment expressions

Show or formulate the shear and bending moment expressions for each board, and plot/draw the shear and bending moment diagrams of the boards.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd