How long will it take for consolidation of a similar clay

Assignment Help Civil Engineering
Reference no: EM13555140

1.Consider a 1000 acre residential area with a housing density of four dwellings per acre. Evaluate the peak hourly water use requirement.

2.A clay specimen, 1 in thick (drained on top and bottom), was tested in the laboratory. For a given load increment, the time for 50% consolidation was 5 min 20 sec. How long will it take for 50 % consolidation of a similar clay layer in the field that is 8.2 ft thick & drained on one side only?

Reference no: EM13555140

Questions Cloud

Calculate the plasticity index the liquidity index : The soil is under a rectangular concrete slab 15m x 50m, used as a foundation for a building. A water pipe, in diameter id located in a trench 450mm below the center of the slab. The trench running along the length of the slab,300mm wide and 450mm de..
Will johnsons actions have any implications for future : In this case, it seems clear why Johnson is tempted to omit references to the ambiguous data. He is understandably anxious to graduate and move on to other challenges in his professional life. He is worried that full disclosure of his findings could ..
Determine the volume and density of the body : The volume and the average density of an irregularly shaped body are to be determined by using a spring scale. The body weighs 7200 N in air and 4790N in water. Determine the volume and density of the body. State your assumptions.
What is the absolute pressure at the surface of the mercury : An airplane is flying at 10.6 km altitude. in its nonpressured cargo bay is a container of mercury 325 mm deep. The container is vented to the local atmosphere.
How long will it take for consolidation of a similar clay : A clay specimen, 1 in thick (drained on top and bottom), was tested in the laboratory. For a given load increment, the time for 50% consolidation was 5 min 20 sec. How long will it take for 50 % consolidation of a similar clay layer in the field that..
Compute the gravimetric water content : A sample of clay was obtained from a point below the water table. An oven-drying test performed on this sample resulted in the following data:
Calculate air-dry moisture content : The weight of a sample of coarse aggregate was measured under various conditions with the following results:
What would be the difference in average annual water require : If 100 acres of farmland were developed for urban housing (four houses per acre), what would be the difference in average annual water requirements after the change over? Assume that the irrigation requirement is 2.5 acre-ft of water for a growing se..
What concentration of ozone is sometime used : What concentration of Ozone is sometime used as a disinfectant for drinking water. Ozone is highly reactive it will react benign species found in water, as well as the pathogens it is intended to kill. It found that ozone reaction in water nearly fol..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the minimum length of curve that can be designed

you are designing a highway to AASHTO guidelines on rolling terrain where the design speed will be 65 mi/hr. At one section, a +1.25% grade and a -2.25% grade must be connected with and equal tangent vertical curve.

  Obtain the dimensionless groups that charactrize the problem

The power loss, p , in a journal bearing depends on length, L; diameter, D; clearance, c; and rotational speed, w. You also have to worry about lubricant viscosity, density, and pressure. Obtain the dimensionless groups that charactrize this probl..

  Verify that there are no outliers in the sample data

The measurements of the nominal shear strength (in kN) for a sample of 15 prestressed concrete beams are as follows: 580 400 428 825 850 875 920 550 575 750 636 360 590 735 950

  Cross-sections of the arch are equilateral triangles

Cross-sections of the arch are equilateral triangles, and (x,y) traces teh path of the centers of mass of the triangles whose area is given by the following equation:

  How to determine maximum positive factored design moments

How to determine maximum positive and maximum negative factored design moments at a certain point

  Total expansion and total bleeding in term of percentage

To avoid shrinkage cracks in the grout, what should be the total expansion and total bleeding in term of percentage for the grout?

  Write an m-file to calculate the factorial function of n

Write an M-file to calculate the factorial function of N!, as defined by: N!=1 N=0 N!=N*(N-1)*(N-2)*...*3*2*1 N>0 The MATLAB code to calculate N factorial for positive value of N would be

  Determine the liquid density in british gravitational units

It is commonly known that there are 16 ounces in 1 lb. Consider a 0.5lbf glass that weighs 1 lbf when filled with 8 ounces of liquid. Determine the liquid density in British gravitational units and in SI units.

  1 the us has produced the following quantity of gauges and

1. the u.s. has produced the following quantity of gauges and potatoes with the price of each listed in dollar

  What is the difference among cement plaster

If the tangents intersect at an angle of 40 degrees, what is the highest degree of curve that can be used?..how to solve this problem using chord basis formula?

  How fast was the car traveling before applying the brakes

The vehicle was estimated to hit the light pole at 30 mph. The skid was 650 feet long. How fast was the car traveling before applying the brakes

  How to calculate the depth of a masonry dam

How to calculate the depth of a masonry dam of trapezoidal cross section with height of 24ft,2ft top width,,12 ft base width and weight of concrete 150 lb/ft^3.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd