How does the change in transistor effect current and voltage

Assignment Help Other Engineering
Reference no: EM131767176

Lab Assignment- Transistor Biasing

Introduction:

Lab is based on the fundamentals of a transistor biasing and the analysis of the circuit.

The goal of Transistor Biasing is to establish a known Q-point in order for the transistor to work efficiently and produce an undistorted output signal. In bipolar transistor circuits, the Q-point is represented by (VCE, IC) for the NPN transistors or (VEC, IC) for PNP transistors.

Review the following videos before getting started with this lab:

1. Watch the video: "Video 3: Fundamentals of breadboard"
2. Watch the video: "Video 4: Basic electrical components"
3. Watch the video: "Video 5: Simple resistive circuit with NI myDAQ"

Materials and Equipment:

Materials:

• Hardware Parts (In the Toolbox):
o An NPN transistor: 2N3904
o Four resistors: 1 kΩ, 470Ω, 3 kΩ and 6 kΩ
o Jumper wires

Equipment:

Hardware Equipment:

o Breadboard
o NI myDAQ Instrument device
o Screw Driver
o Screw Terminal connector
o USB Cable
o Multimeter with probes
o Multimeter from NI ELVISmx Instrument Launcher

Procedure:

This lab has to be implemented only in hardware (using NI myDAQ)

1. Analyze the circuit in the Figure 1 below to calculate the following values: VBB, VE, IE, VC and VCE. Make sure to include 20% tolerance for each resistor in the calculations.

2. Construct the circuit shown in Figure 1 below on the breadboard using the transistor and two resistors (RC and RE).

2242_Circuit.jpg
Figure 1

3. Using the jumper wires, screw driver and screw terminal connector, connect the board to NI MyDAQ Instrument Device.

4. Use channel +15V pin out on the NI myDAQ Instrument Device to provide the supply voltage (VCC). Use channel AI0 to measure the required voltages: VBB, VE and VC and currents: IC and IE using the Multimeter.

5. Tabulate the data from step 1 and step 5.


Calculated

Measured

VBB



VE



VC



IE



IC



6. Short the resistor R2 and calculate the values in steps 1.

7. Modify the circuit in Figure 1 to short the resistor R2 and measure the values in step 4.


Measured values with R2 shorted

VBB


VE


VC


IE


IC


Review questions:

1. Compare a calculated and measured values in the table. Discuss whether the values are the same of different. If they are different, provide the reasoning. And how to reduce this difference between calculated and measured values.

2. What happens when R2 is shorted? Why does the measured values change?

3. If the NPN transistor is replaced with a PNP transistor, how does the change in the transistor effect the current and voltage in the circuit?

Deliverables:

1. Analysis of the circuit and calculations of voltages: VBB, VE and VC and currents: IC and IE.

2. Place your student ID card on the breadboard and take a picture of the circuit board and pin out on the NI myDAQ Instrument Device.

3. Take screenshots of the measurements obtained from function generator and Multimeter on the NI ELVISmx Instrument Launcher on your screen.

Lab Report:

• Use the Lab report template found in the "Tools and Template" link in the navigation center.

• Include all the deliverables.

• Include all the screenshots of the measurements from circuit design on the breadboard using NI myDAQ Instrument Device and measurements from MI ELVISmx Instrument Launcher.

Attachment:- Lab-Report-Template.rar

Reference no: EM131767176

Questions Cloud

Compensated elasticity of labour supply : An individual currently (5) works 2000 hours per year and earns $30 per hour. Find the excess burden of an income tax at 25%.
Prepare the required journal entries : Prepare the required journal entries, The book balance in the checking account of Kyri Enterprises as of November
Discuss effects of poor forecasts on capacities-schedules : Discuss the effects of poor forecasts on capacities and schedules. Discuss the choice of the proper data to use for forecasts.
Calculate the present value index for each alternative : he large trucks are expected to cost $600,000 and to have a four-year useful life and a $60,000 salvage value,Calculate present value index for each alternative
How does the change in transistor effect current and voltage : If the NPN transistor is replaced with a PNP transistor, how does the change in the transistor effect the current and voltage in the circuit?
Explain the ten most important public health problems : Patients need to be involved in their care in order to feel empowered. This will motivate them to take action into their own hands to improve their health .
What is the net present value and irr of the investment : For tax purposes, the entire initial investment will be depreciated by MACRS over 5 years. What is the net present value and IRR of the investment
Problem on active ingredient and various fillers : Pressing pills A drug manufacturer forms tablets by compressing a granular material that contains the active ingredient and various fillers.
Calculate the issue price of the bond : Calculate the issue price of the bond assuming the entire bond is sold on January

Reviews

Write a Review

Other Engineering Questions & Answers

  Characterization technology for nanomaterials

Calculate the reciprocal lattice of the body-centred cubic and Show that the reciprocal of the face-centred cubic (fcc) structure is itself a bcc structure.

  Calculate the gasoline savings

How much gasoline do vehicles with the following fuel efficiencies consume in one year? Calculate the gasoline savings, in gallons per year, created by the following two options. Show all your work, and draw boxes around your answers.

  Design and modelling of adsorption chromatography

Design and modelling of adsorption chromatography based on isotherm data

  Application of mechatronics engineering

Write an essay on Application of Mechatronics Engineering

  Growth chracteristics of the organism

To examine the relationship between fermenter design and operating conditions, oxygen transfer capability and microbial growth.

  Block diagram, system performance and responses

Questions based on Block Diagram, System Performance and Responses.

  Explain the difference in a technical performance measure

good understanding of Mil-Std-499 and Mil-Std-499A

  Electrode impedances

How did this procedure affect the signal observed from the electrode and the electrode impedances?

  Write a report on environmental companies

Write a report on environmental companies

  Scanning electron microscopy

Prepare a schematic diagram below of the major parts of the SEM

  Design a pumping and piping system

creating the pumping and piping system to supply cool water to the condenser

  A repulsive potential energy should be a positive one

Using the data provided on the webvista site in the file marked vdw.txt, try to develop a mathematical equation for the vdW potential we discussed in class, U(x), that best fits the data

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd