Find what is the tracks radius of curvature at the instant

Assignment Help Civil Engineering
Reference no: EM13308463

A race car C is being tracked via telemetry. The on-board acclerometer records and acceleration level of -.7get+.5gen. If you know that the v at this instant is 200km/hr, what is the tracks radius of curvature at this instant?

Reference no: EM13308463

Questions Cloud

Determine the amount of air that must be bled off to restore : When the air temperature is 25°C, the pressure gage reads 210 kPa. If the volume of the tire is 0.025 m3, determine the pressure rise in the tire when the air temperature in the tire rises to 50°C.
Explain employment exit procedures used by two organisations : Explain the employment exit procedures used by two organisations and define exit procedures and compare the exit procedures of the two organisations.
At what constant rate would train need to be decelerating : An excursion train, travelling at 80ft/s, encounters a rain shower. The point A lies directly 8ft. beneath the lip of an overhang in the observation car. The raindrops can be assumed to be falling at a constant speed of 40ft/s.
Find what is the tracks radius of curvature at the instant : A race car C is being tracked via telemetry. The on-board acclerometer records and acceleration level of -.7get+.5gen. If you know that the v at this instant is 200km/hr, what is the tracks radius of curvature at this instant
Find the direction of the acceleration of the smaller object : Three solid spheres of lead, each of mass 9.8 kg, are located at three corners of a square with side lengths of 50 cm. determine the magnitude and direction of the acceleration of the smaller object when it is released
How much annual income would be need to be generated : How much annual income would be need to be generated over a 5 year period to be equivalent to $4,000 over an 8 year period. Consider 6% nominal interest (compounded annually) for both cases.
What is the hydroxide-ion concentration of this solution : A solution has a hydronium-ion concentration of 1.0 x 10^-3 mol per liter. What is the hydroxide-ion concentration of this solution
Determine the current and power : Assume that a 16 volt energy source is in a circuit that has a resistance of 10 ohms. Determine the current and power

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the work done and the heat transfer

Water, initially dry saturated vapour at 4 bar, lls a closed rigid con- tainer. The water is heated until its temperature is 400C. Determine the work done and the heat transfer.

  Determine volume required for trickling filtration treatment

For a flow of 2 MGD, an influent BOD of 200 mg/l, a depth of 8 feet, and a desired effluent BOD concentration of 20 mg/l, determine the volume required for trickling filtration treatment as predicted for single-stage treatment by using NRC equatio..

  Compute the design compressive strength for lrfd

A w14X74 of A992 Steel has a length of 20 feet and fixed ends. Compute the design compressive strength for LRFD and the allowable compressive strength for ASD.

  Calculate the flow rate imprted by the impeller

A six bladed rushton turbine 2.0m in diameter rotating at 25 rev/min in a tank 4m deep, water temperature= 10 degree celcius. For this flocculation system calculate the following: a) Reynolds number

  Determine the maximum allowable length of the box

A square yellow-brass bar must not stretch more than 2.5 mm when it is subjected to a tensile load. Knowing that E = 1.5 GPa and that the allowable tensile strength is 150 MPa

  Calculate ultimate bod where discharge and river meet

Wastewater from a paper mill contains ultimate BOD of 200ppm and DO of 3ppm, water is discharged at a rate of 100,000 gallons per day into a river, the river has a flow of 1 million gallons per day with no BOD

  What are the speed and acceleration of the disks top

disk of radius R=7 in. spins at a constant angular speed of w=500rpm in the clockwise direction. If the disk is released from rest far above the ground, what are the speed and acceleration of the disk's top C point after it has fallen h=3ft

  What minimum size pipe laid on the respective minimum slope

A MH at an intersection has an inflow from three 8-inch PVC (n = 0.01) sanitary sewer pipes laid at minimum slope converging at an intersection and one pipe taking the flow from those three further downstream.

  Determine the detention time of the first pond

Three completely mixed stabilization ponds are connected in series, and the system removes 99.998% from the total coliform count of the influent to the first pond. In stabilization ponds, coliform bacteria are removed by a first-order process

  Determine the magnitude of the velocity of the collar

The undeformed length of the spring is l. Knowing that the collar is released from rest at x = and neglecting friction between the collar and the horizontal rod, determine the magnitude of the velocity of the collar as it passes through point C.

  Is the head loss too great for the design to work

The design parameters are: • Q = 65 m3/d, • Wetland area (A) = 0.23 hectares (2,300 m2) (including the safety factor), • Aspect ratio = 8:1 • Average water depth (d) = 0.5 m • Bed slope = 1% (0.01 m/m) Given that the Manning's resistance factor

  Determine what is the present worth of benefit

A flood control project has a construction cost during the first year of $10 million, during the second year $6 million, and during the third year $2 million. It is completed at the end of the third year and thereafter incurs an annual operating c..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd