Find what concentration would correspond to a risk

Assignment Help Civil Engineering
Reference no: EM13317911

The drinking water standard for tetrachloroethylene is 0.005 mg/L. Using EPA exposure factors for residential consumption, what lifetime risk would this pose? What concentration would correspond to a risk of 10-6? The following data and assumptions apply: Data or Assumption Value Cancer Slope Factor = 5.16 x 10^-2 (mg/Kg x day)^-1 Average Body Weight = 70 Kg Average Lifespan = 70 Years Average Daily Water Intake = 2 L/day Average Time in One House = 30 Years Absorption Factor = 1.0

Reference no: EM13317911

Questions Cloud

What is min required heat transfer rate from heat source : A waste heat source is available at 400°C. A heat engine operates using heat from this source. It rejects heat to the surroundings at 38°C. The power from the engine runs an air conditioner to keep the air inside a building at 25°C
Find temperature at which air must leave heat exchanger : Gaseous oxygen (99% pure, molar basis) is to be produced at a rate of 350ft^3/hr in a Linde single column plant. The column operates at a pressure of 1 atm. Air leaves the compressor at a pressure of 10 atm.
How high did the ball roll before it momentarily stopped : A solid ball starts to roll up a hill with an initial velocity of 50m/s. The ball has a mass of 20 Kg with a 0.75 m radius. How high did the ball roll before it momentarily stopped
How far did the person climb on a frictionless vertical wall : A uniform ladder with a mass of 15 kg is placed on a frictionless vertical wall. An 80 kg person climbs up the ladder. If the coefficient of friction between the floor and the base of the ladder is 0.15, how far did the person climb
Find what concentration would correspond to a risk : The drinking water standard for tetrachloroethylene is 0.005 mg/L. Using EPA exposure factors for residential consumption, what lifetime risk would this pose What concentration would correspond to a risk of 10-6
Determine the mass of the second car : A 9200 kg boxcar traveling at 15.8 m/s strikes a second boxcar moving at 7.11 m/s in the same direction. What is the mass of the second car
How many gallons would be required to last same time as gas : A water treatment plant effluent is to be disinfected with chlorine from ton cylinders of compressed gas. The plant is 5 million gallons per day. There are a total of 10 useable cylinders in the plant.
What is the speed of the ball at the bottom of the incline : A bowling ball of mass 2.7 kg and radius 9.5 cm rolls from rest, What is the speed of the ball at the bottom of the incline
What is the angular acceleration of the wheels : A cyclist starts from rest and pedals such that the wheels of his bike have a constant angular acceleration. What is the angular acceleration of the wheels

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine what is the rate of leakage in gallons per day

An in-ground swimming pool may have a leak. The 30-ft by 10-ft by 5-ft (depth) pool is filled on June 1. On June 13, a hose, flowing at a rate of 10 gallons per minute, is used to add water to the pool. The hose is turned off after 1 hour.

  Calculate the flow rate per unit width of the aquifer

In a water table aquifer bounded on the ends by rivers, the hydraulic conductivity is 50 m/day. The hydraulic heads at x = 0 and x = 1000 m are 100 m and 90 m, respectively.

  Force that cause stress-free

The rigid bar abcd is supported by a pin at B and restrained by identical steel bars at C and D, each of area 250mm 2 . if the temperature is increased by 8 0 C, find out the force P that will cause the bar at c to be stress-free.

  Composition of the remaining liquid phase

At what temperature does the liquid solidify? What is the composition of this last remaining liquid phase?

  How much water must be added to bring the water content

a silty material is to be used to fill an earth damn. How much water must be added to bring the water content of each ton (2000 lb) of the material to 35% if the original watter content is 11.4%

  Determine the magnitude of the maximum shear stress

A torque of T = 3.00 kN-m will be applied to the hollow thin-walled aluminum alloy section. If the section has a uniform thickness of 4 mm, determine the magnitude of the maximum shear stress developed in the section.

  What sample size is necessary for the confident interval

A state legislator wishes to survey residents of her district tosee what proportion of the electorate is aware of her position on using state funds to pay for abortions. a)What sample size is necessary if the 95% Confident Interval

  Determine the maximum efficiency of the cycle

A geothermal power uses hot water (185oF) as a heat source and the cold water from a close by lake (60oF) as a heat sink. The basic operating system is a close loop ammonia efficiency of the cycle that powers turbine-driven electric generator (100..

  Determine at what point does the new method pay off

Assume that a new method allows her to sort 20 rings/min but costs $500 to implement. Is it worth implementing the new method for a batch of 50,000 rings. At what point does the new method pay off.

  Describe the ductility of a reinforced concrete beam

What does under-reinforced mean Which is desirable and why How would your Moment-Curvature plot be affected if the amount of tension steel was doubled How would your Moment-Curvature plot from part a be affected if compression steel was added to the..

  Find time and distance downstream at critical point occurs

Just below the point where a continuous discharge of pollution mixes with the river, the BOD is 10.9 mg/L and the DO is 7.6 mg/L. The river and waste mixture has a temperature of 20oC, a deoxygentation constant of 0.2/day

  Determine what is the normal depth laid on a slope

For a 42-inch concrete stormwater pipe (n = 0.014), laid on a slope of 0.025%, carrying a flow rate of 10 cfs, what is the normal depth

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd