The power dissipated in the resistor R0 is 89 W when connected to a 10V source. Find the total dissipated power if 3 resistors identical to R0 are connected in series to a 10V source. (UNIT:W)

The power dissipated in the resistor R0 is 83 W when connected to a 10V source. Find the total dissipated power if 3 resistors identical to R0 are connected in parallel to a 10V source. (UNIT:W)

How many charged particles were transferred : A glass rod that has been charged to + 17.0nC touches a metal sphere. Afterward, the rod's charge is + 9.0nC |

What is the maximum conductivity can expect from oxide : For use in a liquid crystal display, you want an electrode that is transparent to all visible light. You decide to use a doped semiconducting oxide with a mobility of 10^(-2) m^2/V-s. What is the maximum conductivity you can expect from your oxid.. |

What effect has the dopant addition had on mean free paths : Adding dopants to a sample of silicon is found to reduce the Hall coefficient by a factor of 10 and increase the conductivity by a factor of 5. What effect has this dopant addition had on the mean free path |

Select a topic of interest and explore dualities : Using examples from race or gender, the student will select a topic of interest - Students will explore the dualities and perspectives of a topic and select one position to either support or reject.Using critical thinking skills and theoretical per.. |

Find the total dissipated power if 3 resistors identical to : The power dissipated in the resistor R0 is 89 W when connected to a 10V source. Find the total dissipated power if 3 resistors identical to R0 are connected in series to a 10V source. |

Describe the levers that are available for managers : Describe the levers that are available for managers and individuals to impact individual effectiveness and how those levers work to influence individual performance? What factor(s) do you feel is (are) most important for long term sustainable high.. |

Determine the percent by mass of sodium chloride : Find the percent by mass of sodium chloride in a 1.25M NACL solution. The density of the solution is 1.06g/ml. |

Calculate dopant density represented by silicon cube : The silicon cube you were shown consisted of 4x4x4 unit cells. You were shown one dopant in the silicon cube. Given that the lattice constant of silicon is 0.543 nm. Calculate the dopant density represented by the 4x4x4 silicon cube simulation. |

Explain flask contains pure helium at a pressure of 760 torr : A 255-mL flask contains pure helium at a pressure of 760 torr. A second flask with a volume of 455 ml contains pure argon at a pressure of 722 torr. |

## Find error in voltage which is divided into addiitive errorA sensor voltage vi from a sensor is amplified using the amplifier depicted below on the basis of the following specifications: R1 = 3.9 kW ±0.5%; R2 = 100 kW ±0.5%; |Voff| |

## Specify the equalizer filter e to recover the signalA signal has a band width of 15 hz. The Signal is sampled , quantized and binary coded to obtained a PCM signal. Suppose the reconstruction pulse used is p(t)= rect ( (5t / Ts) - 0.5), where Ts= 1/ fs. Specify the equalizer filter E(f) to recover t.. |

## How much hydrogen mass needs to be converted to energyBriefly discuss the source of solar energy and the processes involved by which the earth receive 5.7kWh/m^2/day over the entire surface. If it becomes possible to simulate the same process on earth |

## Determine the power in the carrier and in the sidebandsAn AM signal is written as xc(t) = Ac (1+ µx(t))cos(2pi*fc*t) where fc is the carrier frequency, Ac is the carrier amplitude, µ is the modulation index, and x(t) is the baseband message signal. We assume that x(t) has absolute bandwidth W |

## What approximate minimum ber is required for voice signalsWhat approximate minimum BER is required for voice signals, data signals and what is the approximate BER level for the optical fiber systems ? |

## Explain the signal transmitted by a base stationThe signal transmitted by a Base Station has a power of 1 mW at a distance of 1 m from the transmitter. Measurements have shown that the propagation exponent for the path loss is n=3 up to a distance of 1 km and n=4 beyond that. |

## What is the maximum number of consecutive bitsWhat is the maximum number of consecutive bits that are in error for a transmission through this channel if the data rate is 10Kbps? If the data rate is 11 Mbps? |

## Calculate the voltage across 480 v windingA single phase two winding transformer having rating: 20 KVA,480/120 V, 60 Hz A source connected to the 480 V winding supplies an impedance load connected to 120 V winding. The load absorbs 15 KVA at 0.8 pf lagging when load voltage is118 V. |

## What is avalanche photodiode noise current per square rootConsider an InGaAs APD with excess noise x=0.7, M=10 where M is the multiplication factor. The unmultiplied dark current is 10 nA and bandwidth is 700 MHz. What is the avalanche photodiode noise current per square root of bandwidth |

## Calculate the electric current moving throughA glass tube with a cross-sectional area of 9^-2 m^2 contains an ionizd gas. The densities are 10^15 positive ions/m^ and 10^11 free electrons/m^3. Under the influence of an applied voltage, the postive ions are moving. |

## In how many ways can a class of 30 students select committeIn how many ways can a class of 30 students select a committe from the class that consists of a president, a vice president, a treasurer, and a secretary A. if any student may serve either of these roles but no student may serve in multiple roles .. |

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd