Find the torsional moment t for the maxiumum shear stress

Assignment Help Civil Engineering
Reference no: EM13300126

The pipe has an outside diameter of 60mm and an inside diameter of 50mm. Find the torsional moment T if the maxiumum shear stress is 80MPa.

Reference no: EM13300126

Questions Cloud

How far from the lens should the object be placed : A converging lens has focal length 10 cm. How far from the lens should the object be placed to form a virtual, upright image twice as large as the object
Solve this model by using graphical analysis : a. Formulate a linear programming model for this problem.
Calculate the angular speed of the merry-go-round : a 30 kg child stands on the edge of a stationary merry-go-round of radius 2.0 m. What is the angular speed of the merry-go-round just after the ball is caught
Explain the following information a+b- : Given the following information A+B-> 2D deltaH=-637.1 KJ deltaS=336.0 J/K C -> D deltaH=544 KJ deltaS=-233.0 J/K calculate ?G° for the following reaction at 298 K. A+B->2C DeltaG=? KJ
Find the torsional moment t for the maxiumum shear stress : The pipe has an outside diameter of 60mm and an inside diameter of 50mm. Find the torsional moment T if the maxiumum shear stress is 80MPa.
Determine the voltage drop across the inductor : A circuit contains a 150-? resistor, a 0.0530-H inductor, a 0.420-?F capacitor, and a source of time-varying emf connected in series. Determine the voltage drop across the inductor
Worker adjustment and retraining notification act : Rajiv has worked for 22 years at a 40-employee branch of a large auto parts chain. Business has been very bad lately, and there are rumors of consolidation, reorganization, even bankruptcy. What protection is Rajiv given under the Worker Adjustment a..
Find the maximum shear stress due to the torsional moment : Member ABC is composed of two sections. Section AB has an outside diameter of 60mm and inside diameter of 50mm, whereas section BC is solid. Find the maximum shear stress due to the 1.5kN·m torsional moment applied at B and the 2.0kN·m moment at C..
How to calculate the approximate enthalpy change : The steam reforming of methane is widely used in industry to make hydrogen, as given in the following reaction:CH4(g) + H2O(g) ? CO(g) + 3H2(g) a) Calculate the (approximate) enthalpy change

Reviews

Write a Review

Civil Engineering Questions & Answers

  Formulate problem as an ip and find optimal solution

The Record-a-Song company has contracted with a rising star to record eight songs. The sizes in MB of the different songs are 8, 3, 5, 5, 9, 6, 7, and 12, respectively. Record-a-Song uses two CDs for recording. Each CD has a capacity of 30 MB.

  Determine what will be the new height of fluid column

A u-tube manometer is used to measure the pressure of a vessel under vacuum. Assume the manometer is open to atmospheric pressure (101.325 kPa) and the density of the fluid in the manometer is 12.0 g/cm3.

  Estimate the aquifer porosity and hydraulic conductivity

A) Estimate the aquifer porosity and hydraulic conductivity, B) determine the flow rate per unit width of the aquifer, C) determine the specific discharge, D) determine average linear velocity of the flow assuming steady unidirectional flow

  What is present worth of five years of cost of maintanance

you purchased an old machine at the beginning of this year.maintanance on this old machine will be 100$ at the end of this year but is expected to increase by $25 each year after. what is the present worth of five years of the cost of maintanance

  Determine the velocity of slider block

Knowing that at t= 3s slider block C has moved 57 mm to the right, Determine the velocity of slider block C at t=0, (b) the acceleration of A and C, (c) the change in position of block A after 5s.

  Determine the specific volume of the exit stream

A stream of Refrigerant-134a at 1 MPa and 12 C is mixed with another stream at 1 MPa and 60 C. If the mass flow rate of the cold stream is twice that of the hot one, determine the specific volume of the exit stream.

  Determine the values of k and c

The landing gear of an airplane can be idealized as the spring-mass damper system. If the runway surface is described y(t)=y0 cos wt, determine the values of k and c that limit the amplitude of vibration of the airplane (x) to 0.1m. Assume m=2000k..

  What will be compacted volume of soil in cy at full site

In addition to performing the cut-and-fill operations, the contractor needs to excavate the entire building footprint to a depth of 8 feet for a basement construction made of concrete masonry perimeter walls supported by 2'-0" X 0'-10" continuous ..

  Supporting Investment Promotion: ERNST & YOUNG

Ernst & young is currently providing support to various sectors. In this regards it was felt that if this report is able to document good practices currently being adopted or planned in ceramic sector.

  Spreader beam and hoisted by a crane

The 3.5mg engine is suspended from a 500 kg spreader beam and hoisted by a crane which gives it an acceleration of 4m/s^2 when it has a velocity of 2m/s. determine the force in chains AC and AD during the lift.

  Determine the maximum safe load for the column

A finished 2 x 4 timber (actual size 1 5/8 in. x 3 1/2 in. x 10 ft long) is used as a fixed-end, fixed-end column. If the modulus of elasticity for the timber is 1600 ksi and a factor of safety of 3 with respect to failure by buckling is specified

  Create a matlab program and flowchart

Create a MATLAB program and flowchart which will allow the user to input an unknown number of temperatures, each of which might be a temperature in Celsius, Fahrenheit, Kelvin, or Rankine, and will convert the user input temperature to each of the..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd