Find the reversible work and the irreversibility

Assignment Help Civil Engineering
Reference no: EM131233798

1. A constant-pressure piston/cylinder contains 2 kg of water at 5 MPa and 100?C. Heat is added from a reservoir at 600?C to the water until it reaches 600?C. Find the total irreversibility in the process.

2. A constant "flow" of steel parts at 2 kg/s at 20?C goes into a furnace, where the parts are heat treated to 900?C by a source at an average of 1250 K. Find the reversible work and the irreversibility in this process.

Reference no: EM131233798

Questions Cloud

Discuss how easy it is to put a value on the given objects : Discuss how easy it is to put a value on the following objects: - An envelope containing foreign currency-say, 10,000 euros, Paintings.
What is the overall impact of change on the organization : In addition to responding to these questions, review the examples of successful change in your textbook and choose two examples to discuss in greater detail. What did you learn from these examples? In each case, how did the individuals overcome ..
Overview on the conflict in the health care system : The Health Care System (HCS) in America: Historical overview on the conflict in the health care system. What is the nature of the conflict within the health care system?
Structure the organization with subsidiary initiatives : A debate continues in board rooms throughout the world about whether to structure the organization with strong corporate (HQ) controls, or structure the organization with subsidiary initiatives (centralized vs decentralized). Which structure do you t..
Find the reversible work and the irreversibility : A constant "flow" of steel parts at 2 kg/s at 20?C goes into a furnace, where the parts are heat treated to 900?C by a source at an average of 1250 K. Find the reversible work and the irreversibility in this process.
Makes the worksheet more attractive : Once you have created a worksheet in Excel, and it functions as you intended. What are some of the ways that you could improve it's appearance? Explain one technique in detail, including how it makes the worksheet more attractive. Try to pick a diffe..
Write a vhdl testbench to verify your design : Draw a block diagram of the complete design that implements your algorithm. Write a VHDL code to model this division by constant circuit. Write a VHDL testbench to verify your design.
What are inflows and out flows : In computing the cost of your M.B.A., should you take into account the loss of salary while going to school?- If you purchase a house and live in it, what are your inflows and out- flows?
Decide what type of communication plan accounting : Decide what type of communication plan Accounting, Inc. uses and what can be improved to make it a better communication plan? Identify what the impact is of Accounting, Inc.'s performance management communication plan.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the normal and shear stresses

The grains of wood in the board make an angle of 20° with the horizontal as shown. Using Mohr's circle, determine the normal and shear stresses that act perpendicular and parallel to the grains if the board is subjected to an axial load of 250 N.

  What is the air velocity in m/s

A 4-m- long, 6-cm-diameter cylinder placed normal to the flow is used to measure the velocity of an air stream. If a force of 50N is measured. What is the air velocity in m/s?

  Determine the normal depth in the channel for a discharge

A natural channel that is clean and irregular(n= 0.040) has a bottom width of 15 ft m, side slopes of 6:1 (H:V) and a bottom slope of 0.0002. Using Manning's equation, determine the normal depth in the channel for a discharge of 720 cfs.

  Why were these chosen for their particular situations

Why were these chosen for their particular situations? Sketch a detail of each partition.

  Find what input of power rating is required for the pump

The average rate of water consumption from this tank is 6.25 kL per day, every day. The farmer refills the tank (overnight) every 14 days, using a pump that takes water from a nearby river. The top of the tank is 53m (vertically) above the level o..

  Develop preliminary wbs for small one-story to be construct

The exterior and interior walls are of concrete block. The roof is constructed of bar joists covered with a steel roof deck, rigid insulation, and built-up roofing.

  Describe what are the different dimensionless groups

What are the different dimensionless groups that describe a golf ball. A golf ball has two velocities, a spin velocity and a forward velocity.

  Establish a horizontal distance

a tape is calibrated and found to measure 100.04ft between the 0- and 100-ft marks. what measurements should be laid out to establish a horizontal distance of 682.25ft?

  Compute the linear error of closure and the precision ratio

Using the data from Problem 6.17, compute the coordinates of stations C, D, E, and A. Assume that the coordinates of station B are 1,000.000 m N and 1,000.000 m E.

  What volume of sludge must digester dispose of each year

WHat volume of sludge must they dispose of each year if their sand drying beds yield a solids concentration of 35%

  Determine the axial stress in the tank wall

A steel scuba tank is 24 in. long and has an external diameter of 7.25 in. and an internal diameter of 6.7 5in. Say the tank is to carry a pressure of 3000psi . Determine the hoop stress in the tank wall. Determine the axial stress in the tank wall.

  What will be the structural weight per meter

What will be the structural weight per meter for IRC class 70r bridge

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd