Find the resulting stress in the steel pipe material if the

Assignment Help Civil Engineering
Reference no: EM13565006

1.If a manometer was used to measure the pressure drop and the fluid in the manometer was an oil with a specific gravity of 0.84, what would the vertical displacement of the oil menisci be for 1 inch of water pressure difference?

2.A steel pipe carries an industrial oil under pressure. The steel pipe inside diameter is 36 in, the pressure head on the fluid is 383.0 ft.

A)- Find the internal fluid pressure in psi?

B)-Find the resulting stress in the steel pipe material if the pipe wall is 3/8 in thick?

Reference no: EM13565006

Questions Cloud

Metal-poor stars found in the milky way galaxy : Where are the majority of older, metal-poor stars found in the Milky Way galaxy? The center of our Milky Way Galaxy can be observed most easilyat which of the following electromagnetic wavelengths? A spiral density wave refers to a region of enhanced..
Moment of inertia of a 0.98-kg bicycle wheel rotating : The moment of inertia of a 0.98-kg bicycle wheel rotating about itscenter is 0.13kg .m2. What is the radius of this wheel, assuming the weight of the spokes can be ignored?
Kinetic energy is translational and how much is rotational : When a pitcher throws a curve ball, the ball is given a fairly rapid spin. If a 0.15-kg baseball with a radius of 3.7cm is thrown with a linear speed of 48 m/s and an angular speed  of 42 rad/s, how much of its kinetic energy is translational and ..
What was the average power output used for this ride : The fastest that anyone has gotten to the top of a local mountain (elevation change of 3500 ft) is 44 minutes. Assume a weight of 160 lb for the bike and rider. What was the average power output used for this ride?
Find the resulting stress in the steel pipe material if the : If a manometer was used to measure the pressure drop and the fluid in the manometer was an oil with a specific gravity of 0.84, what would the vertical displacement of the oil menisci be for 1 inch of water pressure difference?
Find the dry unit weight of the sample : A soil has a total density of 1.80 Mg/m3. When fully dry, the soil has a density of 1.59 Mg/m3. The specific gravity of the solids is 2.57. Find the following soil parameters:
Determine the maximum acceleration of the camera : A camera is packed in a box and surrounded by packing material. The box is dropped vertically onto a horizontal surface. The vertical velocity of the box at the time that it hits the surface is v= 5m/s.
Show that the car must have exceeded the speed limit of 55 : highway patrol officer, you are patricipating in a speed trap. A car passes your patrol car which you clock at 55 mph. One and a half minutes later, your partner in another patrol car situated two miles away from you
Find the magnitude and location of the resultant hydrostatic : A circular hatch is located in a sloping wall of a water-storage reservoir, where the wall slopes at ? = 35° to the horizontal, the radius of the hatch R is 840 mm, and the center of the hatch yC is 3 m below the water surface (measured along the slo..

Reviews

Write a Review

Civil Engineering Questions & Answers

  A root of the linear portion of the stress strain relation

A 32mm rebar with a guage length of 200mm was subjected to tension to fracture according to ASTM E-8 method. The load and deformation data were as shown in table below.

  Determine the magnitude of the couple which is applied

Three shafts and four gears are used to form a geartrain which will transmit 7.5 kW from the motor at A to a machine tool at F. (Bear- ings for the shafts are omitted from the sketch.) Knowing that the frequency of the motor is 30 Hz

  What is the maximum length of trench that can be excavated

What is the maximum length of trench that can be excavated by hand economically rather than by a trenching machine. It will cost $900.00 to transport a trenching machine to the job and back to the storage yard.

  What would the fractional removal of

What is the settling velocity of a floc of diameter 0.15 mm and density 2.12 g/cm3 in water? 2- Will the floc from problem 4 be completely removed in a typical sedimentation basin if alum was used as the coagulant?

  Determine the acceleration of the first two drivers

Three stock car drivers are racing around a circular bend. They are each circling the bend at different radii: r(1)=249 m , r(2)=255 m , and r(3)=261 m . At a given instant, all three are traveling at the same transverse rate of rotation

  Determine the velocity and the volume flow rate of the steam

Steam enters a nozzle at 400oC and 800 kPa with a velocity of 10 m/s, and leaves at 300oC and 200 kPa while losing heat at a rate of 25 kW. For an inlet area 0f 800 cm2, determine the velocity and the volume flow rate of the steam at the nozzle ex..

  Estimate the radon concentration in the crawl space

The house has a dirt-floor crawl spaces (1m high). The emission rate of radon into the crawl space is 0.6 pCi/m^2-s. An exhaust system was added to provide 1 air exchange per hour (ACH) in the crawl space

  Which project will company choose on present value criteria

A company facing an interest rate of 8% must choose among projects offering the following four-year cash flows. If the company is employing the net present value criterion, which project should they choose

  Determine the reaction rate constant to be first order

A reaction in a batch system is assumed to be first order. Data listed below was collected. Determine the reaction rate constant. chemical concentration (ug/L) time(min) 19.3 6

  Superpave designation and maximum size mixture designations

Assuming you have a roadway with 5 million traffic ESALS, and a Nominal Maximum Aggregate Size of 12.5mm, determine the requirements for:

  Draw a flow net show flow lines flow channels and

draw a flow net. show flow lines flow channels and equipotential lines. using flow nets please provide an estimate of

  How the equation for splitting tensile strength of a concret

Need to know how the equation for splitting tensile strength of a concrete cylinder f(ct) = 2P/pi*D*L is derived using mechanics of materials or linear elasticity approach.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd