Find the required width of the footing using terzaghis shear

Assignment Help Civil Engineering
Reference no: EM13296755

A strip footing is founded at a depth 1.5m below the ground surface. The water table is at the ground surface. The footing is supported to carry a net safe load of 400 kN/m^2 with FS = 3. Given Ysat = 20.85 KN/m^3 and phi = 35 degrees, find the required width of the footing using Terzaghi's general shear failure criterion.

Reference no: EM13296755

Questions Cloud

Why are the rules of origin needed for a free-trade area : Why are the rules of origin needed for a free-trade area? How might they be protectionism? (Include at least 2 cited references in APA 6th edition format. Assignment length should be 250-300 words)
What is the projected net present value of this project : The aftertax cost of debt is 4.8 percent, the cost of equity is 12.7 percent, and the tax rate is 35 percent. What is the projected net present value of this project?
Determine what is the design speed of the curve : An equal tangent vertical curve connects a -2% and a +3% grade. The low point of the curve is at elevation 297.88 ft. If the PVI is at elevation 295 ft, what is the design speed of the curve
Find the specific heat capacity of the unknown metal : When 165 grams of an unknown metal at 225 degrees C is placed into 875 grams of water at 24.4 degrees C inside a perfect calorimeter, Find the specific heat capacity of the unknown metal
Find the required width of the footing using terzaghis shear : The footing is supported to carry a net safe load of 400 kN/m^2 with FS = 3. Given Ysat = 20.85 KN/m^3 and phi = 35 degrees, find the required width of the footing using Terzaghi's general shear failure criterion.
Determine the heights of the fluid columns for barometers : Determine the heights of the fluid columns for barometers that use the following liquids at 20 C: water, ethyl alcohol, and mercury. Why do you think mercury barometers were used in the past (before the negative health effects of mercury were know..
How much must you repay him to pay off the loan : Mr. Miser loans money at an annual rate of 73 percent compounded daily. You decide to borrow $10,000 from him and must repay the full principal and interest at the end of 2 years. How much must you repay him to pay off the loan?
The issues are related to the ethical and management : Write an essay on " Companies face lots of issues, and none of them can be overlooked for a fact that they are important. Some of the issues are quite serious in nature and can damage the reputation of the goodwill of the company.
Evaluate how or why the business made such a mistake : Why is knowing (or estimating) the product demand so crucial for a firm? In your response, include an example of a U.S. business that has suffered from poorly estimating the demand of its products.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Write a mass balance equation for this chemical

An industrial plant presently discharges a chemical (W=2000 * 106 gr/yr) to the lake. In addition, the inflow stream also contains the same chemical at a concentration of 15 mg/L. Note that the volumetric inflow and outflow are equal.

  Draw a plan of a typical strip mine

Draw a plan of a typical strip mine showing all operational features and equipment and why is the working slope of an open pit usually much flatter than the final slope?

  Calculate available water capacity

given bulk density as 1300kg/cubic meter and field capacity as 22% by weight and permanent wilting point as 10% by weight calculate available water capacity.

  How much caco3 is produced per hour

A slurry containing 20 percent by weight of limestone (CaCO3) is processes to separate pure dry limestone from water. If feed rate is 2000kg/h, how much CaCO3 is produced per hour?

  Designing the tangent vertical curve

Due to a street crossing a roadway, the elevation of the roadway at station 3 +413.760 must be at 129.388 m. Design the curve?

  Compose a list here of the geological terms

compose a list here of the geological terms that you encounter in this reading that you could not define and explain in a test situation.

  Hydraulic behaviour in open channel

Describe how test flumes and associated equipment are used to assess and confirm hydraulic behaviour in open channel

  Industrial history repeats itself

There are many parallels between the industrialization of the United States after Reconstruction and the modernization of the American workforce in the last twenty to thirty (20-30) years as it transitions from industry to a service-oriented econo..

  Compute the water content

A small chunk of the original sample had a wet weight of 140.9 grams and weighed 85.2 grams after drying. Compute the water content, using the correct number of significant figures.

  Calculate force and moment

Which software do we use to calculate force and moment, and draw shear and moment diagram? I really need this software to design my structural project. Please helps me... thank you so much.

  Determine the maximum force

two links AB and DE are connected by a bell crank as shown. Determine the maximum force that can be safely exerted by link AB on the bell crank if the maximum allowable value for the reaction at C is 1600N.

  Long cantilever beam of elastic modulus

A 45 kg machine is placed at the end of a 1.6 m long cantilever beam of elastic modulus 200 x 109 N/m and cross-sectional moment of inertia 1.6 x 10-5 m4.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd