Find the required depth y as a function of the length x

Assignment Help Civil Engineering
Reference no: EM131196376

The resistance of a beam of uniform width to bending is found to be proportional to the square of the beam depth y. For the cantilever beam shown the depth is h at the support. Find the required depth y as a function of the length x in order for all sections to be equally effective in their resistance to bending

521_5bd99bfe-dcb4-45d4-8548-3d3d12c8bbb5.png

Reference no: EM131196376

Questions Cloud

United states department of agriculture : According to the dietary guidelines from the United States Department of Agriculture, a healthful diet consists of fruits, vegetables, whole grains, lean protein, and dairy.
How many tons of aggregate will be needed : The aggregate in the stockpile contains 2.7 percent moisture. If the required compaction is 95 percent of the target, how many tons of aggregate will be needed?
Determining the total estimated profit : Because you were looking for an interesting job anyway (maximum of 600 hours), you have decided to participate in one or both friends ventures in whichever combination would maximize your total estimated profit. Find the best combination.
Airlines have raised fares to make up for the fuel costs : Fuel Prices Could Squeeze Cheap Flights Airlines are having difficulty keeping prices low, especially as fuel prices keep rising. Airlines have raised fares to make up for the fuel costs. Explain how an increase in fuel prices might cause an airline ..
Find the required depth y as a function of the length x : For the cantilever beam shown the depth is h at the support. Find the required depth y as a function of the length x in order for all sections to be equally effective in their resistance to bending
Explain the major christological perspectives : Explain the major Christological perspectives that were discussed in the Ecumenical Councils of the fourth and fifth centuries.
Investments will she choose if she is risk-neutral person : Currently Lotta £ 95,000 to invest. She faces the following choice: she can buy shares of AstraZeneca and Ericsson. If she invests in AstraZeneca she will lose £ 30,000 with probability 0.5, but with probability 0.4, she will win £ 35,000, while the ..
Overview of the four elements to reduce health disparities : Provide a brief overview of the four elements to reduce health disparities for this population, which include:- Goals, Objectives, Determinants of Health.
Mean-variance and the median : The experiment is to toss two balls into four boxes in such a way that each ball is equally likely to fall in any of the box. Let X denote the number of balls in the first box. Find the distribution of X , its cumulative distribution function, m..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Find the velocity and pressure at (0, 1) and (1, 1)

A source discharging 0.72 m2/s is located at (-1, 0) and a sink of twice the strength is located at (+2, 0). For a remote pressure (far away) of 7.2 kPa, ρ = 1,240 kg/m3, find the velocity and pressure at (0, 1) and (1, 1)

  Design a gear drive for 25 hp in which the input pinion

The crane is expected to operate with a 50% duty cycle for 120 hours per week for at least 10 years. The pinion and the gear of the drive must fit within the 24-in inside diameter of the drum, with the gear mounted on the drum shaft.

  What is the highest possible design speed for the curve

design a horizontal curve for a two lane road. The road has 12 ft. lanes. Due to expensive excavation, it was determined that a maximum of 34 ft. can be cleared from the roads centerline towards the inside lane to provide for stopping sight distan..

  Determine the maximum allowable tensile force

An aluminum link is subjected to axial tension. The loading is limited by the conditions of not yielding and not elongating excessively. The yield limit is satisfied if the stress remains below 50%of the 325M Payield stress.

  Determine final height of the fill after compaction

A 2 m high sandy fill material was placed loosely at a relative density of 47%. Laboratory studies indicated tht the maximum and minimum void ratios of the fill material are 0.92 and 0.53, respectively.

  What is the force needed and the height to pish it upwards

A block with an inclination of 20 degrees has a weight of 60kg, a height of 1.8m and width 1m, static friction is 0.3, what is the force needed and the height (where the force in the box should be) to pish it upwards

  Determine the modulus of elasticity and proportional limit

A tension specimen has a gauge length of 8 inches and a diameter of .505 inches. A load of 9580 pounds was found to develope a stress in the specimen equal to the proportional limit of materials. ( assume that the proportional limit and the yield ..

  Calculations of the complete force analysis

Submit your cost analysis for the materials, along with a scaled drawing of the truss, identifying on the drawing the tensile and compressive force in each member.  Also include your calculations of the complete force analysis.

  Calculate and compare the ozone concentration

Calculate and compare the ozone concentration in ug/m^3 for a polluted day in Mexico City (210 ppbv ozone, 30 C, 0.77 atmospheres pressure) and the ozone concentration in the stratosphere (8 ppmv ozone at 30 km). Use the Standard Atmosphere to get pr..

  A small portion was removed and a moisture content test

An undisturbed cylindrical soil sample is 2.4 in. in diameter and 6 in. long. It has a weight of 1.95 lb. After finding the weight of the entire sample, a small portion was removed and a moisture content test was performed on it. The results of this ..

  How you will place the bars and calculate the location

Concrete cover on both sides. Sketch how you will place the bars and calculate the location of the effective depth. Place as many bars in the lower layers as possible.

  Determine the velocity of the collar at point b for values

To imagine the diagram, the collar at point A (unstretched) is on the same x-axis as the anchor @ C, while the collar point B (stretched) is located downwards-left to point A, forming a 30 degree angle with the y-axis (vertical). In other words, the ..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd