Find the pressure required to fill container at both point

Assignment Help Civil Engineering
Reference no: EM13299969

(1) If intake1 = 0m and intake2 = 0.5m, find the pressure required to fill the container when the height of the fluid is h = 0.75m at both point 1 (intake 1) and 2 (intake 2). Assume the air is at atmospheric pressure until the water level passes intake 2 (at h = 0.5m) and the air follows isothermal compression.

(2) If intake1 = 0m and intake2 = 0.5m, find the pressure required to fill the container when h = 0.75m at both point 1 and 2. This time allow air vent out the top of the container.

Reference no: EM13299969

Questions Cloud

Find the force in each member for a truss not at the ends : Roof trusses such as the one shown are spaced 6 m apart in a long, rectangular building. During the winter, snow loads of up to 1 KN/m^2 (or 1 KPa) accumulate on the central portion of the roof. Find the force in each member for a truss not at the..
What is relevant cost of the new bonds for capital budgeting : Using this informtion above, what is the pre-tax cost of debt for the newly-issued bonds? Also, what is the relevant cost of the new bonds for capital budgeting?
Considered prudent and the safest during pregnancy : Which of the following activities would be considered prudent and the safest during pregnancy? What is athlete's foot an example of?
Find the magnitude of the maximum acceleration of the proton : A laboratory electromagnet produces a magnetic field of magnitude 1.38 T. A proton moves through this field with a speed of 6.06 multiply.gif 106 m/s. find the magnitude of the maximum acceleration of the proton
Find the pressure required to fill container at both point : find the pressure required to fill the container when the height of the fluid is h = 0.75m at both point 1 (intake 1) and 2 (intake 2). Assume the air is at atmospheric pressure until the water level passes intake 2 (at h = 0.5m) and the air follo..
Determine the number of turns in the solenoid : A certain superconducting magnet in the form of a solenoid of length 0.40 m can generate a magnetic field of 14.0 T in its core when its coils carry a current of 95 A. Find the number of turns in the solenoid
Hours per unit annual production total direct : Hours per Unit Annual Production Total Direct
Define the ph of this solution at the equivalence point : A certain weak acid, HA, is titrated with Ka 5.61x10^-6 naoh. More strong base is added until the equivalence point is reached. What is the pH of this solution at the equivalence point if the total volume is 56.0
Find the maximum change on the capacitor : An uncharged capacitor and a resistor are connected in series to a source of emf. If emf = 10.00 V, C = 19.0 µF, and R = 100 ?, find the maximum change on the capacitor

Reviews

Write a Review

Civil Engineering Questions & Answers

  What is the pressure difference between two ends of pipe

The pipe contains two 6 in steel elbows, two fully open gate valves, a fully open 90o angle valve, and a swing check valve. If the discharge end of the pipe is located 20 ft higher than the entrance, what is the pressure difference between the two..

  Calculate the maximum tensile load in n

Consider a cold worked C11000 copper alloy rod 21 mm in diameter and 250 mm in length. Calculate (a) the maximum tensile load, in N, and (b) the maximum length, in mm, to which the rod may be stretched without plastic deformation.

  Determination of edta titration

Does the presence of Mg2+ significantly interfere with the determination of Ca 2+ by the EDTA titration?

  Which method would be most likely to have the conductivity

If an analysis is made of the hydraulic conductivity of a site using permeameter tests of core samples, slug tests of monitoring wells, and pumping tests of production wells, it is often observed that the hydraulic conductivity as measured by each..

  What is the hydraulic conductivity of the other two soils

A permeameter with a cross-sectional area of 400 cm2 contains 3 soils in 50 cm thick layers. A total head difference of 2.0 metres results in a flow rate of 100 cm3/s. The head loss through the top layer of soil is 50 cm.

  What average force was exerted on the ball

After falling from rest from a height of 32 m, a 0.45 kg ball rebounds upward, reaching a height of 22 m. If the contact between ball and ground lasted 1.5 ms, what average force was exerted on the ball?

  Determine the length of the hydraulic jump and energy loss

A spillway carries a discharge of 22.5 m^3/sec with the outlet velocity of 15 m/sec at a depth of 0.2m. Select an adequate USBR stilling basin and determine the sequent depth, the length of the hydraulic jump and energy loss.

  What is the tce concentration in ppm if the tank is held

What is the TCE concentration in ppm if the tank is held at (a) 4 degrees C and (b) 35 degrees C (c) What is the TCE concentration in ppm if the tank is filled with hexane instead of water

  Determine the flow rate of the oil

Oil of a specific gravity of 0.75 is flowing through a 6-in pipe under a pressure of 15 psi. If the total energy relative to the datumplate is 8.0 ft below the center of the pipe is 58.6 ft, determine the flow rate of the oil.

  Comparison between steel structures

Comparison between steel structures and aluminium structures, To make a comparison between Eurocode 3 and Eurocode 9 outlining the main differences

  Mixed liquor volatile suspended solids

For a mixed liquor volatile suspended solids (MLVSS) of 1800 mg/L, what is the total return solids flow rate?

  Determine the operating speeds of the machine

Determine the operating speeds of the machine at which the machine's steady-state amplitude is less than 0.2 mm. Take keq = 3 EI/L3.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd