Find the maximum velocity in the tube

Assignment Help Mechanical Engineering
Reference no: EM13713498

Water at 27 C flows through a tube of diameter d = 50 mm. If the flow is fully-developed and has a mass flow rate of 0.01 kg/s, find the maximum velocity in the tube, and the pressure gradient, dp/dx

Reference no: EM13713498

Questions Cloud

Use the cubic spline method as well : An important fluid property is the kinematic viscosity which determines the viscous, or frictional, forces acting in a flow. The kinematic viscosity of air multiplied by 10^6 is given at 350, 450, 500, 550, and 650 K as 20.92,32.39, 38.79, 45.57, and..
Find the distance from the objective to object being viewed : The focal length of the eyepiece of a certain microscope is 18.0mm. The focal length of the objective is 8.00mm. Find the distance from the objective to the object being viewed
Find the work done by the shopper on the cart : A shopper in a supermarket pushes a cart with a force of 35.0 N directed at an angle of 25.0° downward from the horizontal. Find the work done by the shopper on the cart as he moves down an aisle 50.0 m long
Consider two- dimensional-straight triangular fin of length : Consider a two- dimensional, straight triangular fin of Length L= 50mm and base thickness t= 20mm. The thermal conductivity of the fin is k= 25 W/mK. The base temperature is T_b= 50 degrees Celsius, and the fin is exposed to convection conditions cha..
Find the maximum velocity in the tube : Water at 27 C flows through a tube of diameter d = 50 mm. If the flow is fully-developed and has a mass flow rate of 0.01 kg/s, find the maximum velocity in the tube, and the pressure gradient, dp/dx
Evaluate the thermal efficiency : A quantity of water within a piston-cylinder assembly executes a carnot power cycle. During ISOTHERMAL expansion, the water is heated from saturated liquid at 45 bar until it is a saturated vapor. The vapor then expands adiabatically to a pressure of..
Estimate what is the drag force on a car : What is the drag force on a 1.6 m wide, 1.4 m high car traveling at 11 m/s (25 mph)? Suppose that the density of air is 1.2 kg/m3
Insulated reactor operating at steady state-burns completely : Methane gas (CH4) at 25° C, 1 atm enters an insulated reactor operating at steady state and burns completely with  x % of theoretical air entering at 25°C, 1 atm. Calculate the adiabatic flame temperature (AFT) at x=100, 200, 300 and 400 % and plot t..
How fast is the river flowing : A boat takes 3.20 hours to travel 30.0 km down a river, then 6.80hours to return. How fast is the river flowing

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Assuming that the fluid water is at a temp of 80 f and

measuring a velocity gradient at the surface of a 100 ft2 plate to be 0.5362 sec-1 i assume that this is a typo so i

  Determine the temperature of the outer pipe wall surface

a cylindrical pipe with inner and outer radii of 1.0 m and 1.1 m respectively is comprised of a material such that the

  Show a diagram with the energy fluxes on the pipe

Estimate a value for the convective coefficient, h, with the basis of your estimate and show a diagram with the energy fluxes on the pipe.

  If the maximum and minimum pressures in the cycle are 6 mpa

a closed system contains 0.2 kg of air is used to execute a power carnot cycle between temperature limits of 315 k and

  How many households will that one installation serve

The USEIA reported that in 2011, the average American household consumed 11,280 kWh for the year. On the outskirts of a small city, an energy company has constructed a single, large wind turbine (blade diameter 30 m). A typical average wind speed ove..

  Calculate the temperature k of butane can butane be either

consider 2 kg of butane at pressure of 7.6 mpa in a rigid tank of 0.008 m3 volume.a calculate the temperature k of

  What is the steam quality exiting the low pressure turbine

Reheat is added to an ideal Rankine steam power cycle to improve it’s efficiency and turbine exit quality. Steam enters the HP turbine at 15 MPa and 600C.   Steam exits the HP turbine at 4 MPa and enters the boiler for reheat. Then the steam enters t..

  A lear jet flying at 150 kcas assume no errors due to

a lear jet flying at 150 kcas assume no errors due to compressibility so lets assume 150 keas at sea level on a

  A simple gear train with spur gears that contains a pinion

A simple gear train with spur gears that contains a pinion, an idler, and a gear utilized in order to transmit 10 hp using a train ratio of 4.5:1. The pinion has 14 teeth and the idler has 30 teeth. The input shaft operates at 2000 rpm. The pressure ..

  The chute is deployed is -0003 v2 speed v in feet per

the 230000 lb space shuttle orbiter touches down at about 220 mihr. at 200 mihr its drag parachute deploys. at 35 mihr

  Heat is transferred to the nitrogen in the tank

A 1.2­m3 rigid tank contains nitrogen gas at 200 kPa and 350 K. Now heat is transferred to the nitrogen in the tank and the pressure of nitrogen rises to 900 kPa. The work done during this process is

  Air enters a set of these nozzles at 215 psia and 700

the stators in a gas turbine are designed to increase the kinetic energy of the gas passing through them adiabatically.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd