Find the mass fraction extracted in the turbine

Assignment Help Civil Engineering
Reference no: EM131249891

The power plant using ammonia in Problem 9.71 has a flow of liquid water at 120?C, 300 kPa as a heat source; the water leaves the heat exchanger at 90?C. Find the second-law efficiency of this heat exchanger.

Problem 9.71

Consider the power plant in Problem 9.41. Assume that the high temperature source is a flow of liquid water at 120?C into a heat exchanger at constant pressure, 300 kPa and that the water leaves at 90?C. Assume that the condenser rejects heat to the ambient, which is at -20?C. List all the places that have entropy generation and find the entropy generated in the boiler heat exchanger per kilogram of ammonia flowing.

Problem 9.41

A power plant for a polar expedition uses ammonia and the boiler exit is 80?C, 1000 kPa, and the condenser operates at -15?C. A single open FWH operates at 400 kPa with an exit state of saturated liquid. Find the mass fraction extracted in the turbine.

Reference no: EM131249891

Questions Cloud

Advantages and disadvantages of the ethnocentric : What are the main advantages and disadvantages of the ethnocentric, polycentric, and geocentric approaches to staffing policy? When is each approach appropriate?
Probability of completing project : What is the probability of completing this project within 20 weeks (the joint probability of completing all the paths)?
Explain the trends in the non-alcoholic beverage industry : Describe the trends in the non-alcoholic beverage industry, especially the specific type of beverage category you have chosen. Justify at least three reasons why you have chosen this type of non-alcoholic beverage.
What college-wide changes have occurred or are anticipated : In what way are these changes conflicting with the college's original organizational structure, culture, and/or climate? What type of data should be collected and analyzed in order to identify these conflicts?
Find the mass fraction extracted in the turbine : The power plant using ammonia in Problem 9.71 has a flow of liquid water at 120?C, 300 kPa as a heat source; the water leaves the heat exchanger at 90?C. Find the second-law efficiency of this heat exchanger.
Definition of the social practice approach : In her definition of the "social practice approach" to literacy, Hamilton mentions "the cultural, political, economic practices within which the written word is embedded."
What information do you deduce from these expressions : What information do you deduce from these expressions if A is a promoter, Ba is an activator protein, and C is the activator/DNA complex that makes the gene transcriptionally active?
An activator ba and a repressor protein br : Write down the reactions among Ba, Br, and the complexes formed with DNA (D) that lead to such an input function. Demonstrate that indeed the set of reactions you picked leads to the desired input function.
Describe relationship between ethical leader and follower : What do you believe are the most important characteristics of ethical leadership? Describe the relationship between the ethical leader and the follower. Why is this relationship important for organizations that are attempting to do the right thing?

Reviews

Write a Review

Civil Engineering Questions & Answers

  Calculate heat transfer in process with frictionless piston

A cylinder fitted with a frictionless piston contains 2 kg of superheated refrigerant R-134a vapor at 350 kPa, 100oC. The cylinder is now cooled so that the R-134a remains at constant pressure un- til it reaches a quality of 75%.

  Find what is the flexural rigidity ei of the diving board

Consider a diver weighing 200 lb at the end of a diving board that cantilevers out over 3 ft. The diver oscillates at a frequency of 2 Hz. What is the flexural rigidity EI of the diving board

  What will the cars maximum acceleration be under these

A car is traveling on a paved road with CD = 0.35, Af = 21 ft2, W = 3000 lb, ? = 0.002378 slugs/ft3. Its engine is running at 3000 rpm and is producing 250 ft-lb of torque. The car’s gear reduction ratio is 3.5 to 1

  Calculate the resistance coefficient k for a ball-type

Calculate the resistance coefficient K for a ball-type check valve placed in a 2-in schedule 40 steel pipe carrying 650 gal/min of oil (sg = 0.90)

  Sketch the geometry and orientation of the steps

Sketch the geometry and orientation of the steps formed on the fracture surface.

  Estimate the undrained shear strength at a depth of 2.5 m

Estimate the surface stress to cause the soil at a depth of 2.5 m to yield.

  Determine the length of the swale required with side slopes

The longitudinal slope of the swale is to be 1.5% with side slopes of 5:1 (H:V). If the grassed swale has a Manning's n of 0.030 and a minimum infiltration rate of 200 mm/hr, determine the length of the swale required.

  What bolt sizes must be used for the allowable shear stress

A structural steel beam is attached to a column with bolts. The downward force on the connection is 150 kips. What bolt sizes must be used if the allowable shear stress is 25.0 ksi

  What error results from curvature and refraction

Successive plus and minus sights taken on a downhill line of levels are listed in Problems . The values represent the horizontal distances between the instrument and either the plus or minus sights. What error results from curvature and refraction..

  Determine the quantity of seepage under the piling

A deposite of soil is 16m deep and overlies an impermeable stratum , the coefficient of permiability is 10^-6 m/s. A sheet pile wall is driven to a depth of 12 m in the deposite. The difference in water level between the two sides of the piling is..

  Explain what is the station of the pt before vertical curve

It is known that a horizontal curve starts (has PC) 90m before the vertical curve's PVC. If the superelevation of the horizontal curve is .08 and the central angle is 38 degrees what is the station of the PT

  Importance of mineral identification in applications

What are minerals? Sketch different types of mineral crystal forms and list different types of rock forming minerals. Describe with examples the importance of mineral identification in engineering applications.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd