Find the flow rate in m3 per s when water flows uniformly

Assignment Help Civil Engineering
Reference no: EM13304686

Water flows uniformly in a 6 m wide rectangular channel at a depth of 0.8m. The channel slope is 0.0015 and n=0.014. Find the flow rate in m3/s

Reference no: EM13304686

Questions Cloud

Determine what value of n was used in the design : An irrigation channel is constructed of earth and is 8.1km long and has a capacity of 10 m^3/s for a flow depth of 2m. The cross section is trapezoidal with a bid width of 8 m and side slopes of 2 horizontal to 1 vertical.
Calculate the operating breakeven point in units : Each warmer produced has a variable operating cost of $0.84 and sells for $1.00. Fixed operating costs are $28,000. The firm has annual interest charges of $6,000, preferred dividends of $2,000, and a 40% tax rate.
What is the flow rate for a normal depth of 1m-2m and 4m : A trapezoidal channel with base width 5m and side slopes 2 horizontal to 1 vertical, slopes at 0.0005. If n=0.010, what is the flow rate for a normal depth of 1m, 2m, 4m
What is the present value of her inheritance : Pam Gregg is expecting cash flows of $50,000, $75,000, $125,000, and $250,000 from an inheritance over the next four years. If she can earn 11 percent on any investment that she makes, what is the present value of her inheritance? (Round to the ne..
Find the flow rate in m3 per s when water flows uniformly : Water flows uniformly in a 6 m wide rectangular channel at a depth of 0.8m. The channel slope is 0.0015 and n=0.014. Find the flow rate in m3/s
What is the annual realized return of the three bonds : The current level of the interest rate is equal to 5% per year. During the first year, the interest rate rises from 5 to 10% per year (stays constant afterwards)
Compute the do and initial ultimate bod after mixing : The wastewater treatment plant for Pine City discharges 1 × 105 m3/day of treated waste to the Pine River. Immediately upstream of the treatment plant, the Pine River has an ultimate CBOD of 2 mg/L and a flow of 9 × 105 m3/day.
What is the annula rate of return : You discover an antique in your attic thta you purchased at an estate sale 10 years ago for $400. You auction it in eBay and receive $8000 for your item. What is the annula rate of return?
What is the moment of the tension force acting at a : using the principles to developed in chapter 3 on equilibrium, one can determine that the tension in cable AB is 143.4 N. Determine the moment about the x-axis of this tension force acting on point A.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Describe the use of productivity models for estimating land

Describe the use of productivity models for estimating land productivity. Provide details about various attributes that can be used and how the model is developed . Examples can be used to demonstrate model workability.

  Determine what is the power to use the elbow

An elbow, 90 degrees smooth bend flanged, is used in the Alaskan pipeline. Inside pipe diameter is 48 inches. Flow is 1.6 million barrels a day. 1 barrel=42 gal. Velocity is 8.27 ft/s. SG=0.93

  Find the station and elevation of the low point of the curve

On a certain highway a -6% grade meets a +2% grade at station 70 + 00, elevation 550.97 ft. An equal tangent vertical curve, 800 ft. long, is to be installed to connect these two grades.

  Determine what was the major principal stress at failure

A consolidated-drained triaxial test on a normally consolidated clay yielded a friction angle of 28°. If the all-round confining pressure during the test was 140 kN/m2, what was the major principal stress at failure.

  What length l of splice plate is needed

two strips of a plastics material are bonded together as shown. The average shearing stress in the glue must be limited to 1000 kpa. what length L of splice plate is needed if the axial load carried by the joint is 55 kN and the width (W) is 315 m..

  Calculate the maximum mounding height from the canal

If the hydraulic head in the canal is 100 ft and in the drainage ditch it is 80 ft calculate the maximum mounding height and the mounding distance from the canal that will occur if the farmer irrigates at a rate of 2 acre-ft/acre/year.

  Determine the gravitational force acting between two spheres

Determine the gravitational force acting between two spheres that are touching each other. The mass of each sphere is 400 kg and the radius is 300mm.

  Probability of pulling out vehicle at oncoming traffic

Assuming a standard driver reaction time of 2.5 seconds, what is the probability that the vehicle pulling out will get in an accident with oncoming traffic?

  Determine the actual field weight required to mix a 4 bag

Determine the actual field weight required to mix a 4 bag mix using the mix proportions given below. The excess moisture contet of the sand is 6% and that of the gravel is 2% Component Weight ..

  Determine the smallest standard commercial pipe

For satisfactory operation, the static pressure at the pump inlet must not be lower than -6 m of water gage. Determine the smallest standard commercial pipe that will give the required performance.

  What hydrodynamic model would you use for the system

Solar cookers can be used in less developed countries for cooking and also for thermal disinfection of water. To disinfect water, the water must be heated to about 35 Celsius for 5 hours. Of course, it takes time to raise the temperature of the wa..

  Compute the maximum acceptable service load

Compute the maximum acceptable service load on an A36 steel plate tension member 1/4in.x12in. having a single line of holes parallel to the direction of loading. The load is 25% dead load and 75% live load, and 7/8in. diameter bolts are used.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd