Find the find the force of cd and force acting at a and b

Assignment Help Civil Engineering
Reference no: EM13316679

Draw the free-body diagram of member ABC which is supported by a smooth collar at A, rocker at B, and Find the Find the force of CD, and the force acting at point A & B

Reference no: EM13316679

Questions Cloud

What is its cop operated as a refrigerator : If the efficiency of a reversible engine is 28.%, what is its COP operated as a refrigerator
Aggregate demand and aggregate supply schedules : Suppose that the aggregate demand and aggregate supply schedules for a hypothetical economy are as shown at the top left of the next page. LO3 a. Use the data above to graph the aggregate demand and aggregate supply curves.
Create a class diagram of the intial code : The base application consists of three classes - Doctor, Patient and Hospital. A patient can be a private or public patient and is handled differently in either case. Patients are assigned to Doctors according to availability and preference.
Find the velocity of toyota prius relative to the vw passat : A Toyota Prius driving north at 56.0mph and a VW Passat driving south at 38.0 mph are on the same road heading toward each other, What is the velocity of Toyota Prius relative to the VW Passat
Find the find the force of cd and force acting at a and b : Draw the free-body diagram of member ABC which is supported by a smooth collar at A, rocker at B, and Find the Find the force of CD, and the force acting at point A & B
Advanced analysis assume that consumption schedule : Advanced analysis Assume that the consumption schedule for a private open economy is such that consumption C = 50 + 0.8Y. Assume further that planned investment Ig and net exports Xn are independent of the level of real GDP and constant at Ig = 30 an..
What is the average force felt by tennis ball : What is the average force felt by a 0.06 kg tennis ball if it strikes the racket at a speed of 30m/s and leaves the racket with a speed of 50m/s in the opposite direction
Determine the horizontal and vertical components of reaction : Determine the horizontal and vertical components of reaction at the supports. Neglect the thickness of the beam
Different markets or types of organizational buyers : what are the three different markets or types of organizational buyers? How are they different?

Reviews

Write a Review

Civil Engineering Questions & Answers

  What bolt sizes must be used for the allowable shear stress

A structural steel beam is attached to a column with bolts. The downward force on the connection is 150 kips. What bolt sizes must be used if the allowable shear stress is 25.0 ksi

  Determine the service rate for six vehicles per minute

Vehicles begin to arrive at a toll booth at eight vehicles per minute from 9 A.M. to 10 A.M. The booth opens at 9:10 A.M. and services at a rate of ten vehicles per minute until 9:40 A.M. From 9:40 A.M. until 10 A.M.

  Plot the shape of the water surface from the center

a whirlpool is modeled as the combination of a free and a forced vortex. the maximum velocity in the whirlpool is 10 m/s, and the radius at the juncture of the free and the forced vortex is 10m.

  Calculate the minimum required minimum wall thickness

A tubular aluminium bar (G=28GPa) of square cross section with outer dimensions 50mm x 50mm must resist a torque T=300Nm. Calculate the minimum required wall thickness t_min if allowbale shear stress is 20MPa

  Convert the azimuths from north to bearings

convert the azimuths from north to bearings, and compute the angles, smaller than 180 degrees between successive azimuths 68o06'42", 133o15'56", 217o44'05", 320o35'18"

  Determine the unit strain developed in the concrete

a concrete test cylinder is loaded with p= 100k (445 kn) and resulting shortening of 0.036" (0.0914 mm). determine the unit strain developed in the concrete.

  What is the probability that the vehicle pulling out

what is the probability that the vehicle pulling out will get in an accident with oncoming traffic?

  Calculate the torque required to rotate the inner shaft

a 4ft-long, 1-in-diameter shaft rotates inside an equally long cylinder that is 1.02 in. in diameter. Calculate the torque required to rotate the inner shaft at 2000 rpm if SAE-30 oil at 70 degrees F fills the gap

  Process of mechanical and chemical weathering of rocks

What are minerals and sketch different types of mineral crystal forms and list different types of rock forming minerals. Describe with examples the importance of mineral identification in engineering applications.

  How many light bulbs could be lit with the wasted power

The flow depth and velocity before the jumo are 0.8 m and 7 m/s respectively. The flow depth and velocity after the jump are 2.46 m and 2.28 m/s respectivly. Assuming a flat channel, determine a) the energy loss due to the jump, hl (head loss)

  How far back from the front axle would the center of gravity

how far back from the front axle would the center of gravity have to be to ensure that the maximum tractive effort developed for front and rear- wheel drive options is equal

  How does the engineering classification of soils differ

How does the engineering classification of soils differ from he engineering classification of rocks

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd