Find the final stress in the bar

Assignment Help Civil Engineering
Reference no: EM13548030

1.A circular bar under pure torsion needs to transfer 50 N*m of torque. The total bar length is 1 m and the total rotation can not exceed 2 degrees. The bar is made of a material with G=3000 MPa. What is the minimum diameter of the bar?

2.A bar 25in long attached to one wall was heated by 100 degress F. There is a .5 in gap between the bar and the other wall. The area of the bar is .5 in^2.The coefficient for expansion is .0004/F and the modulus of elasticity is 230 ksi. Find the final stress in the bar.

Reference no: EM13548030

Questions Cloud

Use the euler methods and heun method to solve : Solve the following initial value problem over the interval from t=0 to 2 where y(0)=1 a. Euler method with step h=0.5 b. Midpoint method with h= 0.5
Are x and y independent : Are X and Y independent?
Find stresses in ab and bc and the displacement at point : A bar is under uniform axial loads. AB is 1 foot and has a area of .5 in^2 and BC is 1 foot and has an area of .3 in^2. AB has a 1000lb force putting it under tension and BC has a 500lb force putting it under compression. Find stresses in AB and BC a..
Find the optimal order quantity : Find the optimal order quantity.
Find the final stress in the bar : A bar 25in long attached to one wall was heated by 100 degress F. There is a .5 in gap between the bar and the other wall. The area of the bar is .5 in^2.The coefficient for expansion is .0004/F and the modulus of elasticity is 230 ksi. Find the fina..
Cost concepts - compute variable manufacturing cost per unit : the relevant range, will the fixed manufacturing cost per unit increase, decrease, or remain the same? Explain - Compute Variable manufacturing cost per unit
What is the probability that the operator will be unable : If an operator can handle at most five calls per minute, what is the probability that the operator will be unable to handle the calls in any 1-minute period?
What is the nominal intrest rate on this loan : John Brooks a recent ME graduate from Central Michigan, bought an SUV for $30,000 with a down payment of $10,000. John had a little business on the side and did not have a girlfriend when he was at school and ehnce he was able to save the $10,000 for..
All machines have a life of ten years using incremental rate : The CIMS Co. is considering a new milling machine. They have narrowed the choices down to three alternatives in addition to the Null alternative. The relevant data are shown in the table below

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  Determine the foundation soils allowable bearing capacity

A square footing 2 meters by 2 meters is to be constructed 1.22 meters below the ground surface. The groundwater table is located 1.82 meters below the ground surface.

  Determine ratio of heat supplied to engine to heat removed

a reversible refrigerator removesm heat from sink at 8c and rejects heat to the atmosphere at 15c the refrigerator is coubled to the outputnof a reversible heat engine which receives heat at 577c and reject to the atmosphere at 15c

  Find what is the concentration of the mixture of the stream

A pickle producing plant produces and discharges a waste brine solution with a salinity of 13,000 mg/L NaCl at a rate of 0.14 MGD into a stream. Before the discharge enters the stream, the flow rate of the stream is 1.2 MGD and the salinity is 20 ..

  Plot the relationship between the approach speed v and the

Plot the relationship between the approach speed v and thelength of the dilemma zone for the following data:a2 = 0.5g, δ2 = 1.0s,w = 65ft, L = 15ft, and τ = 4.5s (wherea2 is the acceleration

  Why should the direction of access ramps be sloping down

In designing of access ramps for drainage channels, why should the direction of access ramps be sloping down towards downstream?

  Determine what minimum value of coefficient of traction

A wheel tractor-scraper is operating on a level grade, assuming no power derating is required for equipment conditions, altitude, and temperature.

  Determine the stability of the wall

Determine the stability of the wall before and after the rainfall. Neglect seepage effects and which of the two walls in Figure gives the large horizontal force

  Explain how to estimate the long-term safety factors

A 2.0m-wide strip at a depth of 1 m in a stiff clay carries a wall load of 425 kN/m. The saturated unit weight of the caly is 20kN/m^3. TRiaixal tests give the following results: c'=10 kPa, phi'=28 degree, cu=105kPa, and phi_u = 0.

  How much styrene transfers to the ethylene glycol phase

The distribution coefficient of styrene distributed between ethylbenzene and ethylene glycol at 25 degrees C is .19 mass fraction in the ethylene glycol phase per mass fraction in the ethylbenzene phase.

  Determine the volume-temperature and pressure at all state

Air enters an air - standard Otto cycle with a pressure and temperature of 1 bar and 15 C respectively. The compression ratio is 9 and the bore and stroke of the cylinder are (10 cm, 12 cm).

  Determine what is the average shear stress in the oil

Two parallel plates, one moving at 4m/s and the other fixed, are seperated by a 5mm thick layer of oil of specific gravity 0.80 and kinematic viscocity 1.25 X 10^-4 m2/s.

  Determine the values of theta dot and theta dot at instant

The plate OAB forms an equilateral triangle which rotates counterclockwise with increasing speed about point O. If the normal and tangential components of acceleration of the centroid C

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd