Find the final pressure and temperature

Assignment Help Civil Engineering
Reference no: EM131233376

1. A cylinder/piston contains 1 kg methane gas at 100 kPa, 300 K. The gas is compressed reversibly to a pressure of 800 kPa. Calculate the work required if the process is adiabatic.

2. Do the previous problem but assume that the process is isothermal.

3. A piston/cylinder contains air at 300 K, 100 kPa. It is now compressed in a reversible adiabatic process to a volume seven times as small. Use constant heat capacity and find the final pressure and temperature, the specific work, and the specific heat transfer for the process.

Reference no: EM131233376

Questions Cloud

Determine the pressure and quantity requirements : Determine the pressure and quantity requirements required of a compressor at surface to service the requirements of these rock drills.
What is your multifactor productivity : You are trying to figure out the multifactor productivity of your carrot farm. What is your multifactor productivity, rounded to one decimal place?
Guide to industrial control systems security : Review the NIST Guide to Industrial Control Systems Security.NIST Special Publication (800-82). Specifically review section 6.2, which covers the application of security controls for ICS's.
Is this a one-tailed or two-tailed hypothesis : Using the five steps of hypothesis testing and the 5% significance level (i.e. alpha = .05), does showing the film change students' attitudes towards the chronically mentally ill? What does it mean to set alpha at .05? What is your null hypothesis..
Find the final pressure and temperature : A piston/cylinder contains air at 300 K, 100 kPa. It is now compressed in a reversible adiabatic process to a volume seven times as small. Use constant heat capacity and find the final pressure and temperature, the specific work, and the specific ..
Major assignments of the internship is the development : As you know, one of the major assignments of the internship is the development and completion of a project. While the topic of the project may vary, your responsibility to define and then carry it out does not. With that in mind, what types of issues..
Describe the potential challenges you might encounter : Describe the potential challenges you might encounter in collecting and interpreting your research data and what you might do to minimize these issues - Explain how you would present your data and what presentation format would you use to convey th..
Discuss the principle of life-cycle analysis : Wenson and Gommi Ltd (WGL) produces babycare products. WGL prides itself on its commitment to environmental protection and many of its advertisements focus on its slogan, ‘Taking care of your baby, and your baby’s future’. Discuss the principle of li..
Explore the stanford prison experiment website : Select at least two (2) research methods from the text (e.g., observations, case studies, experiments, etc.), and explain each method's purpose in social psychology. Next, identify at least one (1) situation in which you could apply one (1) of the..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the minimum distance from the diversion that a

A temporary diversion has been constructed on a highway of +4 percent gradient due to major repairs that are being undertaken on a bridge. The maximum speed allowed on the diversion is 10 mph

  Design bridge that will withstand fully loaded semi-trailers

Design a bridge that will withstand 4 fully loaded semi-trailers (eg 2 going in each direction) at the central point, being aware of both static and dynamic loads, the span of the bridge will be 200 meters in length; width is whatever you determin..

  What will be the approximate temperature of the alloy

Is it possible to have a copper-silver alloy of composition 50 wt% Ag-50 wt% Cu that at equilibrium, consists of α and β phases having mass fractions Wα = 0.60 and Wβ=0.40? If so what will be the approximate temperature of the alloy? If such an a..

  Determine the depth of flow and the discharge immediately

A tidal channel, which may be assumed to be rectangular, is 40 m wide and conveys a discharge of 60 m3/s at a depth of 1.52 m. A tidal bore is seen to propagate upstream with a wave speed of 5 m/s.

  What will be the mean velocity in each port

Water enters the lock of a ship canal through 180 ports, each port having a 2 ft by 2 ft cross section. The lock is 900 ft long and 105 ft wide. The lock is designed so that the water surface in it will rise at a maximum rate of 6 ft/min.

  Specify suitable machine screws to be installed in a pattern

Specify suitable machine screws to be installed in a pattern of four, equally spaced around a flange, if the clamping force between the flange and the mating structure is to be 6000 lb.

  Calculate nbspthe pore water pressure which must not be

pore water pressure is to be observed during the construction of the embankment. calculate nbspthe pore water pressure

  What fractionof the total impact of that years emissions of

Weighting these by their global warming potentials, what fractionof the total impact of that year's emissions of these three gaseswould be caused by each gas over the following time periods?

  Determine what is the removal efficiency of the incinerator

A hazardous waste incinerator is to burn 200 Kg/h of PCB waste that is 30 % PCB and 70 % organic solvents. During testing phase, the concentration of PCB in the emission was recorded as 0.025 g/ m³

  Compute the crates velocity two seconds after p has been

A crate has a weight of 50 lb and is acted upon by a force having a variable magnitude of P=20t, where p is in pound and t is in seconds. compute the crates velocity two seconds after P has been applied. The crates initial velocity is 3 ft/s down the..

  Determine the range of values for the distance d

Water flows from a drain spout with an initial velocity of 2.5 ft/s at an angle of 15o with the horizontal. Determine the range of values for the distance d such that the water will enter the trough BC.

  Determine the normalized undrained shear strength

Recommend the undrained shear strength for use in the design of (1) a foundation for an oil tank, and (2) a slope.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd