Find the entropy generation for the process

Assignment Help Civil Engineering
Reference no: EM131233897

1. Air enters an insulated turbine at 50?C and exits the turbine at -30?C, 100 kPa. The isentropic turbine efficiency is 70% and the inlet volumetric flow rate is 20 L/s. What is the turbine inlet pressure and the turbine power output?

2. Carbon dioxide enters an adiabatic compressor at 100 kPa, 300 K and exits at 1000 kPa, 520 K. Find the compressor efficiency and the entropy generation for the process.

Reference no: EM131233897

Questions Cloud

Surveillance important for public health : Why is epidemiologic surveillance important for public health? What role would it play if there were a bioterrorist attack? Discuss
The average time customers spend at the machine : Many of a bank's customers use its automatic teller machine to transact business after normal banking hours. During the early evening hours in the summer months, customers arrive at a certain location at the rate of one every other minute. The averag..
Prepare a memo that you will send to upper-level managers : Review this exhibit in detail and prepare a memo to your boss that summarizes your initial findings and your planned next steps. This memo will be sent to him the day after your initial meeting with him. (1-2 pages, singlespaced, 12-pt font).
Ethics for life as your source : Using Ethics for Life as your source, Please include intro, conclusion and site all ref's Write a 500- to 750-word essay in which you respond to the following:
Find the entropy generation for the process : Carbon dioxide enters an adiabatic compressor at 100 kPa, 300 K and exits at 1000 kPa, 520 K. Find the compressor efficiency and the entropy generation for the process.
Value-added work or non-value-added work : As you think about your experience at the last airport security screening, you wonder which of the tasks that you saw the officers do at the security check were waste, which were non-value-added work, and which were value-added work.  Identify each o..
Kinds of fraudulent or abusive behavior : What kinds of fraudulent or abusive behavior relating to health care services can occur in hospital operations? How does the role of the compliance committee help to monitor and prevent these?
Calculate the turbine exit temperature and power output : Calculate the turbine exit temperature and power output. Also find the compressor exit pressure and temperature.
What extent the security checkpoint is lean operation : You arrive at the airport and wonder to what extent the security checkpoint is a lean operation. Among other things, you observe that it takes about 30 seconds to check an ID, scan a passenger for weapons, and X-ray their luggage. However, the averag..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Calculate the axial forces in members bd and cd

Determine whether or not the truss structure is statically determinate, giving your reasoning. Identify which members in the truss are in tension and which are in compression. Calculate the axial forces in members BD and CD, stating clearly whether ..

  Determine what is the resultant thermal energy

The specific heat (C sub p) of aluminum is 0.214 calories per gram degrees Celsius (0.214 cal/g-C). If a cube of aluminum with a mass of 13.6 kg exhibits a change in temperature of +30 degrees Celsuis, what is the resultant thermal energy

  Determine if the flow will choke and both the downstream

A nearly horizontal, 12 ft wide rectangular channel carries 60 cfs at a depth of 3 ft. the width of the channel is smoothly contracted to 6 ft at the downstream section. (a) determine if the flow will choke and both the downstream and upstream water ..

  List the order in which the components would be assembled

list the order in which the components would be assembled. Is the system glazed from inside the building or outside? How can you tell?

  What fraction of the load p is transmitted by the middle bar

The two outer bars (material A) are identical. The cross- sectional area of the middle bar (material B) is 31.544% larger than the cross- sectional area of one of the outer bars. Also, the modulus of elasticity of material A is twice that of mater..

  Is the head loss too great for the design to work

The design parameters are: • Q = 65 m3/d, • Wetland area (A) = 0.23 hectares (2,300 m2) (including the safety factor), • Aspect ratio = 8:1 • Average water depth (d) = 0.5 m • Bed slope = 1% (0.01 m/m) Given that the Manning's resistance factor

  Find stresses in ab and bc and the displacement at point

A bar is under uniform axial loads. AB is 1 foot and has a area of .5 in^2 and BC is 1 foot and has an area of .3 in^2. AB has a 1000lb force putting it under tension and BC has a 500lb force putting it under compression. Find stresses in AB and BC a..

  How much energy in horsepower islost by the water while flow

A pipeline 1200ft long and 8in. in diameter hasat its inlet point 75ft of available hydraulic energy with respectto the reference level. The velocity in the pipe is 5fps; thepressure at its end is 12psi.

  Determine what the forces are in the ax and ay directions

After drawing a free body diagram, how do you determine what the forces are in the Ax, Ay directions, etc. without being given any numbers

  Where are located the stagnation points

Using the software 2DFlowPlus, investigate the flow pattern resulting by addition of one source (strength +5) at (X = +3, Y = 0) and one sink (strength -5) at (X = -3, Y = 0) in an uniform flow (V∞ = 1). Plot the pressure and velocity field. Where..

  Find infiltration rate assuming that entire crack admits air

A room in a single-story building has three 2.5 x 4 ft double-hung wood windows of average fit that are not weather-stripped. The wind is 23 mph and normal to the wall with negligible pressurization of the room.

  Find the direction of flow

A conical tube of length 8 m fixed vertically with its smaller end upwards. The velocity head and pressure head at upper ends are 1.27 m and 2.50 m respectively. The velocity head and pressure head at lower ends are 0.203 m and 5.407 m respectivel..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd