Find the change in elevation of points a-b and c

Assignment Help Civil Engineering
Reference no: EM13317898

A 1.0-m rigid horizontal support is hung by two cables. One cable is brass and The other cable is high-density polyethylene plastic. At room temperature (21°C), the cables measure 3.50 m vertically. When the temperature drops to 15°C, find the following: (a) The change in length in each cable (b) The change in elevation of points A, B, and C

Reference no: EM13317898

Questions Cloud

Find the magnitude of the impulse imparted by the wall : A rubber ball of mass 149 g is thrown directly at a wall with a speed of 4.7 m/s. what is the magnitude of the impulse imparted by the wall on the ball
What is the pressure at the valve : Water flows through a horizontal pipe of cross-sectional area 10.0 cm2 at a pressure of 0.250 atm. What is the pressure at the valve
What is the magnitude of the net force acting on the vehicle : A 1460-kg racecar is driving around a circular track of radius 161 m. What is the magnitude of the net force acting on the vehicle
Find the total active earth pressure against the wall : The backfill soil's unit weight and angle of internal friction are 17.2 kN/cubic meter and 31 degrees respectively and the angle of wall friction friction between backfill and wall is 20 degrees. Find the total active earth pressure against the wa..
Find the change in elevation of points a-b and c : A 1.0-m rigid horizontal support is hung by two cables. One cable is brass and The other cable is high-density polyethylene plastic. At room temperature (21°C), the cables measure 3.50 m vertically.
What is the maximum charge that can be stored in capacitor : A parallel-plate capacitor is made from two aluminum-foil sheets, each 3.00 cm wide and 10.0 m long. What is the maximum charge that can be stored in this capacitor
Determine point of application from the base of wall : he top of the soil is level with the top of the wall, and the soil carries a uniformly distributed load of 500 psf. Calculate the total active earth force of the wall per linear foot and determine its point of application
Determine the waters speed in the wider pipe : Water flowing in a horizontal pipe is at a pressure of 1.55 105 Pa at a point where its cross-sectional area is 6.00 m2. Find the water's speed in the wider pipe
Estimate cross sectional dimension of bar under strain : A 1000 in diameter solid steel (p= 0.303) bar is 10.0 ft long. Under a tensile load. (a) Estimate the lateral strain experienced by the bar (b) Estimate the cross sectional dimension of the bar when under strain

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the height from the ground at which ball pass

Ball A is thrown vertically upward from the top of a 20-{\rm m}-high-building with an initial velocity of 3m/s . At the same instant another ball B is thrown upward from the ground with an initial velocity of 16m/s .

  What is the average specific gravity of solid constituents

a soil sample is obtained by pushing a 16 in long tube into the side of a pit. the tube has an inside diameter of 3 in. and weighs 1.8 lb. The soil in the tube is trimmed so that its ends are flush with the ends of the tube.

  Determine the basin dimensions

Determine the basin dimensions (width, length, depth) for a detention time of 3 hours and a length to width ratio of 4 to 1. (use English units)

  Determine the maximum load p that can be applied

The 25mm thick strut shown below is glued to the horizontal member along surface AB. The glue can resist a shear stress of 600 kPa before failing, and the horizontal member can resist a normal stress of 2000 kPa before a bearing failure occurs.

  Compute the wavelength corresponding to the frequencies

Provided that the amplitude is sufficiently great, the human ear can respond to longitudinal waves over a range of frequencies from about 20 Hz to about 20000Hz. Compute the wavelength corresponding to these frequencies

  Maximum and minimum stress intensities in the section

Determine the maximum and minimum stress intensities in the section.

  Which design checks that are performed on a clarifier

which design checks that are performed on a rectangular clarifier are not performed on a circular clarifier

  Find what is the tracks radius of curvature at the instant

A race car C is being tracked via telemetry. The on-board acclerometer records and acceleration level of -.7get+.5gen. If you know that the v at this instant is 200km/hr, what is the tracks radius of curvature at this instant

  Calculate the dry unit weight of the compacted earth fill

During construction of a highway project, a soil sample was taken from compacted earth for a sand-cone in place denstiy test. The following data were obtained from the test. Weight of sand used to fill test hole and funnel of sand-cone device= 845..

  Standard test method for flash and fire points

What is the procedure standard test method for flash and fire points by cleveland open cup tester if there is animation or video is better....

  Estimate the force on the chimney and the bending moment

A 10m height chimney has a 2.0m x 2.0m square cross section. The wind blows horizontally in a direction which is parallel to one of the diagonals of the cross section.

  Compute the degree of the curve given the radius r

Use the chord definition to compute the curve parameters L, T, E, M, LC, R, and stations of the PC and PT for the railroad curve with DC = 2deg0'00', I=18deg,0'00' and PI station =25+50.00ft

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd