Find the axial load and total change in each cross section

Assignment Help Civil Engineering
Reference no: EM13320951

A flat bar of cross section 20mm by 70mm elongates 4.0mm in a length of 2.0m as a result of axial load. If the elastic modulus is 199x106 kN/m2 and Poisson's ratio is 0.25 for the material, find the axial load and the total change in each cross sectional dimension.

Reference no: EM13320951

Questions Cloud

If everyone were to obtain music and video content for free : If everyone were to obtain music and video content for free from websites such as MySpace, instead of paying Universal, what would Universal’s producer surplus be from music sales? What are the implications for Universal’s incentive to produce music ..
Explain what mass of water is required for the formation : The reaction of coal and water at a high temperature produces a mixture of hydrogen and carbon monoxide gases. This mixture is known as synthesis gas (or syngas). What mass of water is required for the formation of 175 grams of carbon monoxide? C(..
What will be the steady-state concentration of selenium : Plateau Creek carries 5.0 m^3/s of water with a selenium (SE) concentration of 0.0015 mg/L. a farmer starts withdrawing 1.0 m^3/ of the creek water to irrigate the land.
Use what you learned in part a to explain whether or not : You are considering selling your vintage 1969 convertible Volkswagen Beetle. If the car is in good condition, it is worth a lot; if it is in poor condition, it is useful only as scrap. Assume that your car is in excellent condition but that it costs ..
Find the axial load and total change in each cross section : If the elastic modulus is 199x106 kN/m2 and Poisson's ratio is 0.25 for the material, find the axial load and the total change in each cross sectional dimension.
Explain the vapor pressure of ethanol is 100 : The vapor pressure of ethanol is 100. mmHg at 34.9°C. What is its vapor pressure at 53.5°C. (?Hvap for ethanol is 39.3 kJ/mol.) _____ mmHg
What is the final charge on the capacitor : a 1.50-uf capacitor charged to 40.0 v and a 2.40-uf capacitor charged to 12.0v are connected to each other, What is the final charge on the 1.50-uf capacitor
Can you determine precisely by how much producer surplus has : Can you determine precisely by how much producer surplus has increased as a result of the $14.82 increase in the average fare? If you cannot be precise, can you determine whether it will be less than, or more than, a specific amount?
Determine the normal stress in each portion of the rod : A polystyrene rod consisting of two cylindrical portions AB and BC is restrained at both ends and supports two 6 kip loads. Knowing that E = 0.45 * 10^6 psi,

Reviews

Write a Review

Civil Engineering Questions & Answers

  Calculate the steady-state pollutant concentration in lake

Conditions in the sewage pipe are Qs= 0.5 m^3/s, and Cs= 100mg/L. The pollutant is destroyed in the lake with a first-order rate constant of 0.2/d. The flow rate out of the lake is 5.0 m^3/s.

  Calculate the deflection of the beam

Also calculate the deflection of the beam to check that it complies with the design limit of L/200. Only variable actions are required for deflection check.

  What error in pressure drop would ensue if assumptions made

horizontal pipe, and the fanning friction factor is f_F = 0.0060. what error in the pressure drop would ensue if the assumption were made that the flow was laminar, abandoning the previous value of the friction factor.

  Determine what is the hydraulic gradient of piezometers

The bottom of piezometers A and B are on the same flow line and 1000 m apart. The bottom of piezometer A is at 130 m and its water level is 160 m. The bottom of piezometer B is at 100 m and the water level is 150 m.

  Determine what the forces are in the ax and ay directions

After drawing a free body diagram, how do you determine what the forces are in the Ax, Ay directions, etc. without being given any numbers

  Determine the resulting acceleration of the crate

THe 50 kg crate is stationary when the force P is applied. Determine the resulting acceleration of the crate if (a) P=0, (b) P=150 N, and (c) P=300 N

  Determine force exerted by the hydraulic cylinder on boom

A hoist mechanism is attached to the back of a pickup truck. The crate being moved by the hoist shown below weighs 200 lbs. Note: Point A is directly above point B and the vertical distance between points A and B is 16 inches.

  Provide expression for velocity and acceleration of airplane

The path of the airplane is described by the equation y=kx^2, where k=6 x 10^-4 m^-1. Provide the expression for the velocity and acceleration of the airplane when x=390m. Express the velocity in m/s and the acceleration in m/s^2.

  Determine the greatest weight of the flower pot

if each cord can sustain maximum tension of 50N before it fails, determine the greatest weight of the flower pot the cords can support

  Determine what should the after burner temperature be

An afterburner has been selected to destroy 99.9% of the ethane (CH3-CH3)in a gas (mostly air) stream . if the residue time is 0.8 seconds and the pressure is 1.1 atmospheres in the after burner,

  Determine length of roadway that is in full superelevation

Determine the length of roadway that is in full superelevation for a four-lane expressway with a 60 mph design speed. The BC of the curve is at station 15+00 and has a minimum allowable radius. The curve delta is 25 degrees and 30'.

  Determine what is the value of degree for the sand

A square footing 0.3 m by 0.3 m is placed on the surface of a dense cohesionless sand (unit weight = 18.2 KN/m^3) and subjected to a load test. If the footing fails at a load of 13.8 KN, what is the value of (degree) for the sand

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd