Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
9000 MW are to be transmitted from a hydraulicpower plant to a load center located 500 km away from the plant . Find the surge impedance load and based on the practical line loadability determine the number of three phase,60 Hz lines required to transmit this power, with one line out of service (hints add one more line to whatever obtained)) for the following case: (a) 345 kV lines with Zc= 297 ohm (b) 765 kv lines with Zc= 266 ohm
Assume Vs=1.0 pu Vr= 0.95 pu and delta=35' (practical line lodability crieteria) Also asuume that the lines are uncompensated and widely seprated such that there is negligible mutual coupling between them.
A. Make a two bit counter with The input X =0 makes the counter count from 0-3-1-0 and X=1 goes from 0-1-2-3-0. Choose two different types of flip flops to implement it. B. Describe what will happen on your circuit when the present state is 2 and ..
Semiconductor A has a bandgap of 2.5eV while semiconductor B has a bandgap of 1.5eV. What is the ratio of the intrinsic carrier concentrations in the two materials (niA/niB) at 300K
Imagine a network layer packet that travels from one host to another host across multiple local area networks interconnected by routers, Explain how the packet moves from device to device through the network.
Develop a state diagram for a sequential circuit that has two input terminals (W and X) and two output terminals (Y and Z). When three consequtive 1's are detected on W, Y will become 1.
Select f and K so that the steady-state error to a ramp input is less than or equal to 25% of the input magnitude.Determine the percent overshoot for a step input for the design selected in part (b).Use MATLAB to plot y(t) for a step input R(s).
Two point charges q1 = 2.0 C and q2 = 1.0 are fixed in a plane at the positions given by the Cartesian coordinates shown in the figure at right. Consider that they are in a vacuum, where ko = 9.0 × 109 N.m2/C2.
A tow truck applies forces F1 and F2 to the bumper of an automobile where F1 is horizontal. Determine the magnitude of F2 that will provide a vertical resultant force, and determine the magnitude of this resultant.
A process worker received an electric shock when she attempted to turn off a conveyer control. The toggle switch controlled the power to a variable speed drive. An examination found that dust had accumulated on the toggle switch. Moisture on the ..
Data at a rate of 2 Mbps is to be transmitted via a pass-band communication system whose carrier frequency is 500MHz. A binary antipodal system with roll-off factor of 0.2 is used for this communication.
A pn junction with Nd=4x10^16 cm^-3 and Na=3 x 10^15 cm^3 experiences a reverse bias voltage of 1.6V (a) Determine the width of the depletion region and the junction capacitance per unit area
1. What is Miller capacitance What is its role in High frequency amplifier design Label all the involved variables in the Figure below and derive an expression for the Miller effect capacitances (input and output).
An ARM processor with 32-bits address and data buses is connected to three areas of memory implemented as three types of chips. The address is a byte address. A 16M Byte EEPROM implemented using EEPROM chips that are 4Mx8-bits
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd