Determine what value is required for the second resistor

Assignment Help Electrical Engineering
Reference no: EM13258009

A voltage divider is required to produce a 5.5 v output from a 12 v source. If one of the resistor values is 1.0 k, what value is required for the second resistor so that the voltage across the 1.0k resistor is 5.5v

Reference no: EM13258009

Questions Cloud

Explain the football games for state university. : Katherine D'Ann is planning to finance her college education by selling Programs at the football games for State University. There is a fixed cost of $400 for printing these programs.
Find surge impedance load and based on practical line : Find the surge impedance load and based on the practical line loadability determine the number of three phase,60 Hz lines required to transmit this power, with one line out of service.
Find the frequency corresponding to the cutoff wavelength : When light of wavelength 350 nm falls on a potassium surface, electrons having a maximum kinetic energy of 1.31 eV are emitted. find the frequency corresponding to the cutoff wavelength
Blood vessle from the right ventricle to the lungs : If the pressure in the right ventricle is 10 mm Hg and the pressure in the blood vessle from the right ventricle to the lungs is 15 mm Hg, is the one way valve between these two open or closed? Does blood flow from ventricle to vessel under this cond..
Determine what value is required for the second resistor : A voltage divider is required to produce a 5.5 v output from a 12 v source. If one of the resistor values is 1.0 k, what value is required for the second resistor so that the voltage across the 1.0k resistor is 5.5v
Create a list of three best practices : Create a list of three best practices that not only would have helped the company you researched from failure, but would also apply to the rest of the industry your company was part of. Explain your rationale for selecting these best practices.
Prepare a flexible manufacturing budget for relevant range : Prepare a flexible manufacturing budget for the relevant range value using 20,940 unit increments IN EXCEL.
Prepare an income statement for the month ending : After its first month of operation, the following amounts weretaken from the accounting records of Sandcastle Realty Inc. as ofJune 30, 2009. Prepare an income statement for the month ending June 30,2009.
Analyze the variables : Analyze the variables, as listed on page 5 and explained in the following pages, that describe some of the challenging differences between domestic and IHRM.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Calculate the output for each system for given input

The signal x(t)=10cos(t)+10sin(10t) is input into the following systems: a) \(H(s)=100/(s^{2}+10s+100)\) b) \(H(s)=s^{2}/(s^{2}+10s+100)\) calculate the output for each system.

  Sketch the spectrum of the original signal nd sampled signal

a. Sketch the spectrum of the original signal and the sampled signal from 0 kHz and 25 kHz. b. Sketch the recovered analog signal spectrum if an ideal lowpass filter with a cutoff frequency of 4 kHz is used to filter the sampled signal. X(f) 10k 2..

  How many bits will be used to store 2 min of digital signal

The analog signal cos (200t) is digitized using a sampling frequency of 300 Hz, and a quantization of 8 bits per sample. How many bits will be used to store 2 minutes of the digital signal

  What would be the baud rate if the intial value of the timer

Write a sequence of instructions to initialize and run the timer to geneate an 800 baud rate clock. what would be the baud rate if the intial value of the timer was set to 9AH

  Determine the impedance of the unknown material

A 150 MHz uniform plane wave in normally incident from air onto a material whose intrinsic impedance is unknown. Measurements yield a standing wave ratio of 3 and the appearance of an electric field maximum at 0.3 wavelengths

  Determine the quasi-steady-state output voltage

The NMOS transistors in the circuit shown in Figure P16.68 have parameters Kn =0.2mA/V2,VTN =0.5V,λ=0,andγ =0.(a)Forgatevoltagesof φ = 2.5 V, determine the quasi-steady-state output voltage for (i) vI = 0

  What might be one function of the large boxes

view an electrical substation that delivers power to a manufacturing plant, you notice large boxes with two terminals connected by wires to the substation network. What might be one function of these large boxes

  Define write-back write allocate

How do we deal with a L1 cache that is Write-back Write allocate, and the L2 cache, which is a Write-through Write no-allocate?

  What is minimum nd maximum value of load voltage for circuit

A zener regulator circuit has a load resistance that varies between 470 ohms and 2700 ohms. The circuit uses a 10V zener diode, Rs = 330 ohms, and the source voltage is 24V. The zener resistance is 10 ohms and the zener test current (Izm) is 28mA.

  Discuss key quantities from a zener diode data sheet

Discuss some key characteristics of "load lines". What information does a load line provide you. Discuss key quantities from a zener diode data sheet. What are most important for a circuit designer.

  Define design with multiplexer

Define Design with Multiplexer, Design a circuit using one 16 TO 1 multiplexer with W, X,Y,Z on the control inputs

  What is the output voltage of differentila amplifier

In the differential amplifier shown in the schematic, R1 = R2 = 10 k ohm; R3 = R4 = 100 k ohm. Assume the ECG voltage at V1 = 100 mV, and the ECG voltage at V2 = - 100 mV. There is a power line interference of 200 mV at both input sites.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd