Find out the exit temperature

Assignment Help Mechanical Engineering
Reference no: EM13138165

Determining the Exit Temperature and Power Input of Air through a Compressor
Air at 150Pa and 310K enters a compressor of inlet diameter 2cm. The Compressor raises the pressure to 3.5 times the inlet pressure and has an outlet diameter of 5cm. Determine the exit temperature and power input required, if the mass flow rate of air is 100kg/hr.

Reference no: EM13138165

Questions Cloud

Company break-even point in dollar sales : Scott Company's variable expenses are 70% of sales. The company's break-even point in dollar sales is $2,420,000. If sales are $53,000 below the break-even point, the company would report a:
Market price of the stock : The company issued to the stockholders 100,000 rights. Ten rights are needed to buy one share of stock at $34. The rights were void after 30 days. The market price of the stock at this time was $36 per share.
What would be the necessary journal entry : On December 31, 2007, Drew Company issued $170,000, five-year bonds for $155,000. The stated rate of interest was 6 percent and interest is paid annually on December 31. What would be the necessary journal entry?
Financial leverage characteristic of long-term debt : The financial leverage characteristic of long-term debt results in:
Find out the exit temperature : Determining the Exit Temperature and Power Input of Air through a Compressor, Air at 150Pa and 310K enters a compressor of inlet diameter 2cm. The Compressor raises the pressure to 3.5 times the inlet pressure
Enty to record depreciation expense : on january 1, 2011, Sesame revised these estimates to a total useful life of 4 years and a salvage value of $10,000. Prepare Sesame's enty to record 2011 depreciation expense.
Computing temperature water evaporation : Calculating temperature, water evaporation, and heat in a power plant cooling situation. In a nuclear power plant the cooling tower system must be run on a closed cycle.
Interest costs throughout construction : The contractor was paid $2,200,000. An assessment made by the city for pavement was $6,400. Interest costs during construction were $170,000.
Define two infinite parallel plates are separated : Two infinite parallel plates are separated by a distance h. The space between them is filled with a Newtonian fluid: density (rho), viscosity (mu). The lower plate is fixed

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the tension t in the cable

System of force and cable tensions is in equilibrium and what are the necessary conditions for static equilibrium and determine the area moment of inertia about Ox for the area shown under the curve

  Explain what is the tangential force

A spur gear has 48 teeth with a diametral pitch of 8 and a pressure angle of 20 deg. The face width is 0.75 inches. If the gear is transmitting 25 HP at 250 rpm

  Explain force exerted on the body by the fluid motion

In flows past solid bodies, the force exerted on the body by the fluid motion depends upon the fluid velocity u, the density p, the viscosity

  Plot data using appropriate dimensionless groups

Assume that viscous effects are negligible Plot this data using appropriate dimensionless groups

  Minimum weight design of a variable shape three-bar truss

Obtain a new solution, and determine whether any buckling constraints are active. If no buckling constraints are active for L = 10 in., re-run the analysis by increasing L , and estimate the value of L at which at least one buckling constraint b..

  Explain beam deflection at corner through centroid

Beam deflection at corner through centroid, Sometimes the term centroid throws me for a loop. So, how would I set this problem up?

  Explain layer of steel on the inner surface

An oven door consists of a layer of asbestos sandwiched between a layer of steel on the inner surface and a layer of wood on the outer face

  Calculate the actual a/f ratio and do a wet

Find the stoichiometric A/F ratio (by mass) for the combustion of benzene (C6H6). Compute the actual A/F ratio and do a wet and dry analysis of the products by volume at a mixture strength of 95%.

  The effect of fluid cooling

Write a  literature review and the title is "the effect of fluid cooling on the performance of building integrated photovoltaic thermal systems. Using some BIPVT prototypes measure their thermal and electrical output and dtermine their effectiveness"

  Compute the force required to punch out a rectangular

Calculate the force required to punch out a rectangular hole 100m x 50mm in a 2mm thick aluminium sheet. The ultimate strength in shear is 125 MN/m^2.

  Determine the maximum shear stress

Draw the Mohr's circle for this stress state, deterrnine the principal stresses and the angle of the principal direction to the x-axis and determine the maximum shear stress.

  Explain piston-cylinder assembly undergoes a constant

Refrigerant R-134a vapor in a piston-cylinder assembly undergoes a constant-pressure process from saturated vapor at 800 kPa to 50 ºC.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd