Find length of pipe needed to bring water to saturated vapor

Assignment Help Civil Engineering
Reference no: EM13321187

Saturated liquid water at 1000 kPa flows at 2 kg/s inside a 10 cm outer diameter steel pipe and outside of the pipe is a flow of hot gases at 1000 K with a convection coefficient of h = 150 W/m2 K. Neglect any T in the steel and any inside convection h and find the length of pipe needed to bring the water to saturated vapor.

Reference no: EM13321187

Questions Cloud

Calculate the per day costs for crashing : Calculate the per day costs for crashing each activity and which is the most attractive activity to start crashing? Why - How would you ensure that the construction workers do not delay the project or decrease the quality of work due to lethargy and..
What is the rotational inertia of this object : A large metal ring has a radius of 0.30 m and a mass (uniformly distributed) of 2.5 kg. The ring hangs from a nail as shown. What is the rotational inertia of this object
Determine the corresponding value of the normal stress : a 60 -m- long steel wire must not strech more than 48mm when the tension in the wire is 6 kn. determine the corresponding value of the normal stress.
Explain why your chosen product would be a good candidate : Identify a product that could be promoted using a social networking site such as Facebook. In about 100 words, explain why your chosen product would be a good candidate for a social networking-based promotion strategy.
Find length of pipe needed to bring water to saturated vapor : Saturated liquid water at 1000 kPa flows at 2 kg/s inside a 10 cm outer diameter steel pipe and outside of the pipe is a flow of hot gases at 1000 K with a convection coefficient of h = 150 W/m2 K.
Regardless of whether the short run or the long run is being : Regardless of whether the short run or the long run is being considered, a firm should continue to operate as long as its price is greater than its average variable cost
Why does carlos use the atm more frequently : Interest Rates and ATM Trips.Carlos, who lives in a country where interest rates are very high, goes to an ATM every day to get $10 of spending money
Determine the asd reference and adjusted design values : Determine the ASD reference and adjusted design values for the following members and loading conditions. All members are Select Structural Southern Pine and are fully braced to prevent lateral torsional buckling.
Performance based factors and measures for quality assessmen : Performance Based Factors and Measures for Quality Assessment

Reviews

Write a Review

Civil Engineering Questions & Answers

  How many gallons of water are contained in the tank

Develop a table that shows: 1) How many gallons of water are contained in the tank if the volume is measured in increments of 1 ft from the bottom to the top. 2) The mass of water at each increment, expressed in lbm.

  Determine the velocity v2 of the particle

The motion occurs in the horizontal x-y plane. Determine the velocity V2 of the particle at the end of the 3-s interval.

  Compute the maximum acceptable service load

Compute the maximum acceptable service load on an A36 steel plate tension member 1/4in.x12in. having a single line of holes parallel to the direction of loading. The load is 25% dead load and 75% live load, and 7/8in. diameter bolts are used.

  Ompare the ratio of kinetic energy to the potential energy

If a unit mass of groundwater accelerates from rest to an average linear velocity of 1 m per year and climbs a vertical distance of 1 m, compare the ratio of kinetic energy to the potential energy of the unit of groundwater.

  What is max amount of benzene that the company can discharge

A company near City X want's to know how much benzene they can release into River Y. City Z is 85.5 miles downstream from City X. City Z doesn't want to have Benzene levels higher than 0.0000015 g/L.

  Find dry unit weight of the sample and water content

An undisturbed soil sample was collected in a sampling tube of internal diameter 5cm. The length of the extracted sample was 10.2 cm and its mass was 360 g. After oven drying the mass reduced to 326.5 g.

  Find probability of atleast one tractor is in good condition

A construction firm purchased 3 tractors from a certain company. At the end of the fifth year, let E1, E2, E3 denote, respectively, the events that tractors no. 1, 2, and 3 are still in good operational condition.

  Explain what type of heat transfer mechanism is employed

A 40 oF breeze of 10 miles per hour blows over the top of a round open-top water cooling tank which has a bulk temperature of 100 oF. What is the rate of energy in kW that enters into the air What type of heat transfer mechanism is employed in thi..

  Design a curve for the highway by computing the radius

The PI is at station 250+50, the design speed is 65mi/h, and a maximum superelevation of 0.07 ft/ft is to be used. If the central angle of the curve is 38 degrees, design a curve for the highway by computing the radius and stationing of PC and PT.

  Determine what is the rate of water to be added to the tank

A hole at the bottom of a fish tank releases water at a rate given by the free jet equation. The hole at the bottom has a .5" diameter. If the water level is desired to be at 2' high and be at steady state,

  Determine what is the point b ellipse height

H = h - N Point B has a geoid correction of -100', and a NAVD88 elevation of 100'. What is the point B ellipse height

  What height difference is needed to generate the flow

A siphone generates a flow of 1 ft/sec thru a 1 inch OD, 3/4 ID hose. A) What height difference is needed to generate this flow B) What height for 10 ft/sec C) What for 100 ft/sec

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd