Find degree of saturation

Assignment Help Civil Engineering
Reference no: EM13546680

A moist soil sample wights 346g.After drying at 105 degree celsius it then wights 284g.the specific gravity of the mass and of the soil is 1.86 and 2.70.

find:

1.water content

2.void ratio

3.degree of saturation

4.porosity

Reference no: EM13546680

Questions Cloud

Compute the ratio of the nominal flexural strength of the : Compute the ratio of the nominal flexural strength of the beam to the maximum service load moment, and compare your findings to the ACI load factors and strength reduction factor.
Derive an expression for acceleration in cylindrical : Perform this calculation using cylindrical coordinates. Cylindrical coordinates are the same as polar coordinates, with the addition of a third, z-axis.Recommend that the z-axis be placed up the axis of rotation for ?.
Compute the required weight of coarse aggregate per cubic : A concrete mix with a 3 inch slump, water cement ratio of 0.50 and sand with fineness modulus of 2.4 contains 1700 lb/yd^3 of coarse aggregate, compute the required weight of coarse aggregate per cubic yard
Objective mirror of the reflecting telescope : The 200-inch-diameter objective mirror of the reflecting telescope at the Mt. Palomar Observatory has a focal length of 17 . Part A The -number of a mirror is defined exactly the same as the -number of a lens. What is the -number of this mirror?
Find degree of saturation : A moist soil sample wights 346g.After drying at 105 degree celsius it then wights 284g.the specific gravity of the mass and of the soil is 1.86 and 2.70.
Equilibrium while the puck on the tabletop revolves : An air puck of mass m1 = 0.23 kg is tied to a string and allowed to revolve in a circle of radius R = 1.3 m on a frictionless horizontal table.
What total cylinder length l is required for the platform : The floating platform shown is supported at each corner by a hollow sealed cylinder 1 m in diameter. The platform itself weights 30kN in air, and each cylinder weighs 1.0 kN per meter of length
What force is applied to the lid : A 22.5 cm screwdriver is used to pry open a can of paint. If the axis of rotation is 2.29 cm from the end of the screwdriver blade and a force of 79 N is exerted at the end of the screwdriver’s handle, what force is applied to the lid? Answer in unit..
What is the total mechanical energy of the oscillator : Consider a simple pendulum with L = 2.4 m and m = 1.8 kg. Suppose the mass is initially at rest at the lowest point on its trajectory when it is given an impulse such that it then has a velocity of 0.17 m/s. What is the total mechanical energy of the..

Reviews

Write a Review

Civil Engineering Questions & Answers

  What happens after the memory is full

Assuming approximately 19,296 data points can be held in memory, with a 21X Datalogger (CR23X Micrologger), capturing battery voltage; panel temperature

  What is the weight of the gate per meter of length

An 800 ft ship has a displacement of 35,000 tons, and the area defined by the waterline is 38,000 ft^2. Will the ship take more or less draft when streaming from salt water to fresh water? How much will it settle or rise?

  How many days are required for the concentration to reach

The degradation constant is 0.2 1/d. If the initial concentration is 100 mg/L, how many days are required for the concentration to reach 0.14 mg/L

  Consider x and y independant gaussian random variables

consider x and y independant Gaussian random variables with zero means and unity variance. 1. for an arbitrary new random does the following hold p(x,y/z)= p(x/z)p(y/z)? 2. let z= x+y. write the explicit expression of the pdf p(x,y/z). use the Dir..

  Determine whether wall has adequate sliding resistance

Whether the wall has adequate sliding resistance and whether the wall is safe against over-turning

  Compute the maximum acceptable tensile load

Compute the maximum acceptable tensile load Pu, on an angle L6x4x3/4 when connected to both legs. The 4 in. leg contains a single gage line of 7/8in. diameter bolts, and the 6in.

  Sketch how you will place the bars and calculate

Concrete cover on both sides. Sketch how you will place the bars and calculate the location of the effective depth. Place as many bars in the lower layers as possible.

  The corresponding increase in the diameter of the vessel

A spherical gas container having an outer diameter of 15 ftand a wall thickness of 0.90 in. is made of a steel for whichE =29*106 psi and v = 0.29. Knowingthat the gage

  Find expressions for the acceleration components ax and ay

A steady, incompressible two-dimensional velocity field is given by the following components in the xy-plane u = 0.205 + 1.72x + 0.851y v = -0.509 + 0.953x - 1.72y

  Consolidation ratio of the soil at the unloaded condition

An increment of vertical stress of150kpa compress the sample to a void ratio of1.43. What is the over consolidation ratio of the soil at the unloaded condition.

  Design a rectangular reinforced concrete beam for the span

design a rectangular reinforced concrete beam (tension steel only) for the span and superimposed service loads shown. use f'c=5000psi and A615 grade 60 steel. LL=3.5 k/ft over the first 12 feet of the beam

  Calculate as many principal or maximum strains

a point within an elastic body was subjected to a system of planestress. strain gauges were used to measure that would allow for thecalculation of principal strain and stress values at that point.with the given information

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd