Explain the meaning of the reliability index ß

Assignment Help Civil Engineering
Reference no: EM13528822

Explain the meaning of the reliability index,β, and how it relates to failure / survival inthe context of bridge design? What is the value ofβ we use in design?

Reference no: EM13528822

Questions Cloud

What will be the value of xafter executing the above switch : If x = 3, then what will be the value of xafter executing the above switch statement?
Alsogive the parameter rating in each of the fiveclasses : Giving the classes, explain how rocks are put intofive (5) classes by each of the above parameters. Alsogive the parameter rating in each of the fiveclasses. Hint; use a table to answer this question
Discuss the applicability of grouting technology inimproving : Rock masses that donot have the desired properties for a givencivil engineeering application are improved. The method of choicedepends on the purpose for which the rock mass is intended. amongthe common methods for increasing the strength of fissured..
Explain each of the parametersin the equation is obtained : According to barton(1974) the quality of a given rock mass can bedetermined using the equation below. explain each of the parametersin the equation is obtained.
Explain the meaning of the reliability index ß : Explain the meaning of the reliability index,β, and how it relates to failure / survival inthe context of bridge design? What is the value ofβ we use in design?
Compute the following assuming hl93 loading is the live load : Compute the following assuming HL93 loading is the live load.Draw loading diagrams so I can see the placement of your loads forALL cases considered.
Design the mosteconomical truss that will support the load : A bridge having a horizontal top cord is span between tow piers Aand B having an arbitrary height. It is required that apin-connected truss be used, consisting of steel members boltedtogether to steel gusset plates. The end supports are assumed to be..
The initial and after-consolidation void ratio of the sample : A saturated sample of soil, 38mm in diameter and 75mm high, hasbeen prepared for a triaxial test. Total mass of the sample was measured as 144.6grams, and the initial moisture content determined at 25.2%. The Specific Gravity of thesolids was estimat..
Would it still be normally consolidated with the water : Estimate the value of the coefficient of at-rest earth pressure forthe deposit. If, when the water table was at the ground surface, the deposit was normallyconsolidated,would it still be normally consolidated with the water tablelowered? A reason mus..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine what is the density of the soil solids

During a shrinkage limit test on a silty clay, the volume of the dry soil pat was found to be 11.02 cm3 and its dry mass was 22.78 g. If the shrinkage limit was 10.9, what is the density of the soil solids

  Describing a dynamic programming algorithm

Describe a dynamic programming algorithm to find an independent set of T such that the sum of numbers of nodes in the set is the largest among all possible independent sets of T.

  Give beam deflection solution

Beam Deflection Solution, Derive an expression for the deflection due to shear for a cantilever beam of constant rectangular cross section, under action of a point load, P at free end.

  Calculate the carbon content required at surface of steel

A 0.02wt% C steel is to be carburized at 1200°C in 4 hrs with a point 0.6mm beneath the surface reaching 0.45wt%C. calculate the carbon content required at the surface of the steel.

  Write brief paragraph summarizing habitat simulation method

Write a brief paragraph summarizing the following Habitat Simulation Method used to analyze environmental flow requirements.

  Estimate the annual et losses in inches for the area

For a drainage area of 5,187mil^2 mean annual runoff is determined to be 3,708ft^3/s and the annual averge rainfall is 35.5 inches. Estimate the annual ET losses in inches for the area.

  What return period must an engineer use in the design

What return period must an engineer use in the design of a bridge opening for a 50% risk that flooding will occur at least once in two consecutive years? Repeat for a risk of 100%.

  Calculate the required downpayment and monthly payments

Terry wants to purchase a used car for $8000. The dealer offered to finance the deal at 8.5% APR for 4 years with 10% down payment. Terry's bank will provide a loan at 7.8% for 3 years, but wants a 20% downpayment.

  The bridge cable is stiffened by a three hinged stiffening

a suspension bridge cable of span 100 m and central dip 10 m is suspended from the same level at two towers. the bridge

  Measured tape length should be corrected by

An invar  tape haviong a nominal length of 100ft and a croos -sectional area of 0.005sq in. was standardized under a tesion of 15lb. when the tape wa

  Determine the critical point tc and the critical do

If the critical point in a DO sag curve is found to be 18km downstream from the discharge point of untreated wastewater, would you expect the critical point to move upstream (toward the discharge point)

  Find the unknown quantity in each of the formulas and tables

find the unknown quantity in each of the following, using the standard series equivalence formulas and tables in the Appendix. Give preference to the approach yielding the fewest computational steps.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd