Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
An open system Brayton cycle is used in a power plant. The atmospheric inlet conditions of the compressor are: temperature 30C and pressure 100kPa and the pressure at its outlet is 1200kPa. The volumetric flow rate at the inlet of the compressor is 150m^3/min. At the exit of the turbine the temperature is 500°C. The Compressor and turbine have isentropic efficiencies of 82 and 88 percent respectively and the heat in is 2065 kW. Using variable specific heats
Determine:
a) The net power output
b) The thermal efficiency
c) The back work rate
d) Show with procedure and explain how you would solve problem if the Qin was not given.
You do not need to get numbers for this problem.
The oven exhaust gases are available at 250 F. Assume that the design temperature and residence time have been established as 1300 F and 0.6 sec, respectively. The type of burner used in the process requires outside air at a moass ratio of 12:1
Ethylene diamine tetra-acetic acid (EDTA) is a water-soluble compound that readily combines with metals, such as calcium, magnesium, and iron. The molecular formula for EDTA is C10N2O8H16. Assume one EDTA molecule complexes (associates with) one m..
Water flows through a 200 m long ,30 cm diameter steel pipe with surface roughness 0.046 mm at a rate of 0.25 m^3/s .Find the pressure(P2)considering both friction and minor losses
An ideal reheat rankine cycle operates between the pressure limits of 20 kPa and 10 MPa, with reheat occuring at 3 MPa. The temperature of steam at the inlets of both turbines is 500 C
Design a simply supported one-way reinforced concrete floor slab to span 10 ft and carry a service live load of 175 psf and a service dead load of 25 psf. Use fc' = 3000 psi and fy = 60,000 psi.
Determine the base of the following arithmetic operation(assume that the base fo the stystem is x)
The maximum flexural stress on a transverse cross section of a beam2" x 4" with a rectangular cross section must not exceed 8 ksi.Determine the maximum resisting moment Mr that the beamcan support if the neutral axis is
There are two ways to get from City One to City Three, (a) directly or (b) via City Two. Let A be the event that the road from City One to Three is open. Similarly, B is for City One to Two and C is for City Two to Three.
Calculate the (maximum) design load on a hollow AISI 1020 steel shaft with an outside diameter of 2.5 inches and an inside diameter of 2 inches. Assume a safety factor of 2.
As a highway patrol officer, you are patricipating in a speed trap. A car passes your patrol car which you clock at 55 mph. One and a half minutes later, your partner in another patrol car situated two miles away from you, clocks the same car at 5..
A rural town with sewered population of 4,500 has a daily wastewater flow of 1,590 m3/day with an average BOD of 280 mg/L including industrial wastes. The industrial discharges to the municipal sewers are 57 m3/day at 1,800 mg/L BOD from a slaughterh..
Influent sample collected from a wastewater treatment plant was analyzed for various solids concentrations. Results indicated concentrations of Total Volatile Solids (TVS)
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd