Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A spindle-bracket assembly uses the following parts: a steel spindle, two nylon bushings, a stamped steel bracket, and six screws and six nuts to attach the nylon bushings to the steel bracket, and thereby support the spindle. Com pare this assembly with the spindle-bracket assembly shown in Problem 16.65, and estimate the assembly efficiency for each design.
Problem 16.65
The design shown in Fig. P I6.65 is proposed for a metal tray, the main body of which is made from cold-rolled sheet steel. Noting its features and that the sheet is bent in two different directions, comment on various manufacturing considerations. Include factors such as anisotropy of the rolled sheet, its surface texture, the bend directions, the nature of the sheared edges, and the way the handle is snapped in for assembly.
uniform rod makes with the vertical during the roll, and (b) the speed of the roller after it moves 4 ft., starting from rest. The roller rolls without slipping, and the rod hangs vertically (theta = 0) when the system is at rest.
An air-water vapor mixture at 0.1 MPa, 35 C and 70% relative humidity occupies a volume of 100 m^3 Determine the humidity ratio, the dew point, the mass of dry air in the volume and the mass of water vapor in the volume.
The design capacity of a steel pile is 250 kN. The pile is driven by a steam hammer with a manufacturer's hammer energy rating of 36 kN • m. Determine the average penetration of the pile
A 300 acre parking lot has a runoff coefficient of 0.8 and a time of concentration of 40 minutes. Using the rational method (Q=CIA), what is peak Q if a 4"/hr rain falls for 10 minutes
Calculate the pH of a buffer solution prepared by mixing 8.5g KH2PO4 with 43.5g K2HPO4 in 1 liter of water (this is actually the composition of the dilution water used in a BOD test. Follow the same procedures you have been using for previous acid/..
Compute the volume of a waste sludge with 96% water content containing 1000 lb of dry solids. If the moisture content is reduced to 92%, what is the sludge volume
House chilled water is available for cooling coming from 6-in dia. chilled water line carrying chilled water at approximate constant 40 degree F temperature. Chilled water pressure in the 6-inch line is 110psig.
The cross-sectional geometry of bone varies along its length, although the cross-section can be approximated as hollow and circular, with an average outer diameter of 27 mm and inner diameter of 14 mm
Two water reservoirs A and B are connected to each other through a 40 m long, 2 cm cast iron pipe with a sharp-edged entrance. The pipe also involves a swing check valve and a fully open gate valve.
A vertical pipe of 4ft diameter and 60 ft long has a pressure head of 22.7 ft of water at its upper end. when the flow of water through it is such that the mean velocity is 16 fps, the pipe friction head loss is hf = 2.8 ft.
The aluminum honeycomb is 2 cm thick. the cells are in the shape of 0.5com squares and the walls of the cells are 0.1mm thick. the density of epoxy resing is 1.25g/cm3.
The vertical deflection in a simply supported beam follows the following equation: v = -[(w_0*x)/(360LEI)](7L^4 - 10*L^2*x^2 + 3*x^4) What is the equation for the applied load w(x)
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd