Draw the binding moment and shear force digram

Assignment Help Civil Engineering
Reference no: EM13780201

Q1. On figure above, Use the slope-deflection method to:

a- calculate the support reactions in the beam shown below

b- calculate the sheare force and binding moment

c- draw the binding moment and shear force digram

1198_Calculate the support reactions in the beam.png

Q2.

By using moment distribution,Determine the support reactions in the continuous beam ABCD,

Determine the bending moment and shear force and draw the diagram for them

1543_Calculate the support reactions in the beam1.png

Use the technique below to solve this question:

Step.1

Stiffness of a member (k)

Stiffness of AB = kAB =

• Stiffness of BC = kBC =

• Stiffness of CD = kCD =

Step.2

Distribution factor (DF)

• DFBA =

• DFBC =

• DFCB =

• DFCD =

Step.3

Fixed-end moments (FEM)

Member AB

MAB =

MBA =

Member BC

MBC =

MBC =

Member CD

MAB =

MBA =

Step.4

Make table for your question as the table on different example below :

1879_Calculate the support reactions in the beam2.png

Finally, draw the diagram for bending moment and shear force.

Q3.

On the figure below

The composite bar shown in the figure below is initially unstressed The coefficien unit temperature change, respectively, while the corresponding values of Young`s modulus are ES and EA.

a- If the temperature of the bar is reduced by an amount of T uniformly along its length, find an expression for the tensile stress induced.

b- If the temperature of the bar is increased by an amount of T uniformly along its length, find an expression for the tensile stress induced.

2351_Calculate the support reactions in the beam3.png

Reference no: EM13780201

Questions Cloud

Demographics and community resources : In Section 1 of your course project, Demographics and Community Resources, you will:
Assignment on email harassment : Suppose you are an internal investigator for a large software development company. The Human Resources Department has requested you investigate the accusations that one employee has been harassing another over both the corporate Exchange email sys..
Quality management organizations-one national : Prepare a 350 word paper in which you research at least two quality management organizations-one national and one local-that would positively enhance the implementation of a quality program.
Corporate environment-dealing with ethical issues : Assume that you are a manager within a corporate environment, and you are presented with an ethical dilemma. Suggest viable approaches to resolving the dilemma. Rate your comfort level with dealing with ethical issues. Provide one (1) example that su..
Draw the binding moment and shear force digram : Calculate the support reactions in the beam and calculate the sheare force and binding moment - draw the binding moment and shear force digram.
Extraterritoriality : Extraterritoriality is:
Explain the importance of product quality : Explain the importance of product quality and discuss how marketers use quality to create value. Do you feel that Apple or Samsung offers a better value proposition for their customers? If so, why? Provide examples.
Ordination of women : Why is the ordination of women such a central issue both for women and for many religious communities, including communities on both sides of the issue?
Media coverage of terrorist attacks influence : You have been selected to lead the media campaign for ISAF. Through extensive liaison, you have been allowed to write 1 article that will run simultaneously in the major news publications throughout the United States, Europe, Afghanistan, and Paki..

Reviews

Write a Review

Civil Engineering Questions & Answers

  What is your speed in mph and ft/s need formulas

You are driving a car your metered fuel flow is 5.97x10^5 csf if at the speed you are driving you are getting 40mpg what is your speed in mph and ft/s need formulas.

  Calculate what is the flow rate of water over a length

The pressure drop in a 10 cm galvanized iron horizontal pipe (ks=.15mm) carrying water over a length of 50 m is 30 kPa. What is the flow rate

  What is nominal yearly interest rate on a loan with interest

what is the nominal yearly interest rate on a loan with quarterly interest of 3% with quarterly compounding

  Type of reaction involving protonated alcohol

The reaction between 2-methyl-2-pentanol and HBr to yield 2-methyl-2-pentene is probably: A) an E1-type reaction involving the protonated alcohol as the substrate. B) an SN2-type reaction involving the protonated alcohol as the substrate.

  Determine the centroid for the region bounded by x-axis

Determine the centroid for the region bounded by the x-axis, the curve y=x^3, and the line x=3

  Calculate amount of suspended solids accumulating each day

A sedimentation basin is used to remove suspended solids from a wastewater. The rate of flow of wastewater into the tank is 10 L/s, and the influent concentration of suspended solids is 200 mg/L.

  Determine the volume of the spherical tank to be used

A spherical tank is being designed to hold 7 moles of methane gas at a pressure of 8 bar and a temperature of 50oF. Determine the volume of the spherical tank to be used.

  Determine how high of a signal source impedance can exist

How high of a signal source impedance can exist and still provide an output signal from an inverting amplifier circuit. Explain

  How to compute the elevation of points at stations

Tabulate station elevations for a 200-ft equal-tangent parabolic curve with g1= -1.25%, g2= +1.25%, VPI station = 146+00, and VPI elevation = 1,895.00 ft. Compute values if stakeout is at 30-ft increments. Check by second differences

  At what point on expressway should motorist step on brakes

At what point on the expressway should the motorist step on her brakes in order to reduce her speed to the maximum allowable on the ramp just before entering the ramp

  What is the elongation of a rectangular bar

What is the elongation of a rectangular bar (cross section 2 inch * 2 inch length 4 ft) When it is subjected to an axial load of 80,000 lbs. Assume the material of the bar has the following properties G = 7,700 KSI, V =0.30

  Determine the minimum length of a crest vertical curve

Determine the minimum length of a crest vertical curve if the grades are +4% and -2%, Design speed is 70 mi/h

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd