Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Datapath Control for a Sequential Divider The algorithm and a corresponding fl owchart for calculating the division num / den between two integers were presented in figure 11.13 . In that case a complete divider was developed, whereas in this case we are interested in the same division but using a datapath (in other words, a control unit is needed here).
(a) Based on the algorithm of figure 11.13(and on the several examples using a datapath shown in chapters 3, 5, and 11), sketch a datapath that seems adequate for this problem.
b) Draw a state transition diagram for a (Moore) control unit such that the desired division is produced by your datapath.
Two balanced three-plia.se loads that are connected in parallel are fed by a three-phase line having a series impedance of (0.4 + j2.7) ohm per phase. One of the loads absorbs 560 kVA at 0.707 power factor lagging
Running at 1200 rpm from a 280-V source, a series-connected dc motor draws an armature current of 25 A. The field resistance is 0.2Ω, and the armature resistance is 0.3 Ω. Assuming that the flux is proportional to the field current, determine the ..
You are planning to buy a $250,000 house and will take out a mortgage for 80% of the homes value. The term of your mortgage is 15 years and the interest rate is 4%, compounded monthly.
Find the total impedance Zt, in rectangular and polar.- R1=2 ohms, R2=10 ohms Xc=6 ohms - (B) R1=1k ohm, R2=4k ohms,Xl1=3k ohms,Xl2=7k ohms.
Find the final yield for a nine-mask-level process in which the average fatal defect density per cm2 is 0.1 for four levels, 0.25 for four levels, and 1.0 for one level. The chip area is 50 mm2.
An analog LTIC system with impulse response function h(t) = u(t+2) - u(t-2) is presented with an input x(t) = t(u(t) - u(t-2)). a) Determine and plot the the system output y(t) = x(t)*h(t). b) Is this system stable Is this system casual
Given a circuit description such that count the number of cars in the traffic junction.the traffic light red signal should always be on,but get off when green light is on.Green signal is on for time equal to the number of cars.For example,if 3 is ..
Can you think of an explanation for the two peaks in the histogram? Is there some consideration other than height that results in the two separate peaks? What is it?
Incremental Update. Typically, after every hop at least one packet header field (e.g., a packet's time-to-live field) needs to be overwritten. Because the checksum is a simple complement of a 1s complement sum, it turns out that when, for instance..
A steady voltage of 0.75V is applied to an op amp integrator having component values of R = 200 k and C =2.5 μF. Assuming that the initial capacitor charge is zero, determine the value of the output voltage 100 ms after application of the input.
If the op amp provides a slew rate of 1 V/ns, what is the highest input frequency for which no slewing occurs?
Determine the estimated service demand load in volt-ampres and amperes @ 240V for a residence having the following characteristics- 2500 sq ft
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd