Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
For the following scenarios tell whether you think a refraction survey or a reflection survey would give better results and explain why. Also state how you think the geophone strands and seismic source should be set up (examples: refraction survey with shots at either end or both ends, or a reflection survey with a shot in the center)
1) You have been hired to do a survey to search for old tunnels that are rumored to be in the area, previously used to smuggle people across the US-Mexico border. The tunnels are not expected to be exceptionally deep underground.
2) You are doing a survey to contour the water table across a 2 mile stretch of land between a river and a farmer's field. He wont let observation wells be drilled in his field, but the water table data needs to be gathered.
3) A basalt flood plain covers what archaeologists believe to be the ruins of a stone castle and its surrounding farmland. When a rift erupted approximately 500 years ago the basalt flows covered the already demolished castle. The basalt layer is thick enough that it could conceal rubble from stone walls and foundations and would not be easy to dig through or see through with ground penetrating radar. Also, Do you think a seismic survey could locate the buried castle ruins in the middle of the buried farmland?
You arrive at your bus stop at some random point in the cycle, what is your expected wait time, w(t), to board a bus. Be sure to show your work or you will lose points. What is the standard deviation in w(t) given the fact that there is no bus wait..
Finally, the train decelerates uniformly for another kilometer before coming to rest at station B. If the time for the whole journey is six minutes, draw the v-t graph and determine the maximum speed of the train.
An open rectangular tank contains water up to about half its depth. this tank accerlerates at a=2.2m/s2 up a slope of alpha, which causes the free water surface to form an angle theta with the horizontal plane. what is angle aplha of the slope
how would the determination of bulk specific gravity of fine aggregate be affected by the 500g sample being drier than
water from a waste water treatment plant is released into a receiving pond that has a volume of 5 ac-ft. one of the reasons for doing this is to assure that the chlorine residual is below 0.1mg/L before the water is released to a stream as require..
A venturi meter is used to measure flow velocity. Given the manometer reading at A is 100 kPa, D = 10 cm, d = 5 cm, VA = 2 m/s, and specific weight of water is 9800 N/m3.
A spherical drop of water has r = .1mm . If the surface tension of water is 72 dynes/cm, calculate the pressure difference across the interface. Express the answer in dynes/cm^2. (Tip: theta = 0 for perfect fluid spheres)
A beam of w16 X 50 section has a simple span of 20 ft. The beam is subjected to a uniform load of 2 kips/ft and an axial tensile force of 10 kips. Determine the maximum tensile and compressive stresses in the beam
a horizontal curve on a single-lane highway has its PC at station 124 + 10 and its PI at station 131 + 40. The curve has a superelvation of 0.06 ft/ft and is designed for 70 mi/h. What is the station of the PT?
The pulley at B is connected to a motor that is driving the system. The other three pulleys are consuming the power delivered by Pb . Pa = 20kW, Pb = 75kW, Pc = 30kW, and Pd = 25kW and the shaft is rotating at 120rpm.
After injecting 50 MMSCF (14.7 psia and 60 oF), the pressure increase from 2500 to 3500 psia. Deviation factors for the gas are 0.90 at 3500 and 0.80 at 2500 psia and the bottom-hole temperature is 160 oF. What is the cubic feet of gas storage spa..
This material is related Geotechnical Engineering, please only answer if you are certain and sure of your answer. An undisturbed soil sample has a dry unit weight of 112 pcf with a specific gravity of solids equals to 2.68.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd