Distance from the roadway to the floor of the vehicle

Assignment Help Civil Engineering
Reference no: EM13542372

You are in charge of evaluating the safety (hazard) of a low water crossing. Traffic surveys show that the "Aaverage"vehicle using the crossing is semi-rectangular in shape (10 ft long, 5 ft wide, and 4.0 ft high - not including the distance from the roadway to the floor of the vehicle, 1.5 ft), and weighs approximately 3,000 lbs. Assume the vehicle, including the engine compartment is completely sealed. Each tire has about 1 ft by 0.67 ft of tire tread in contact with the road surface. Assume that the specific weight of the water flowing is 62.4 lb/ft3 (likely a low estimate since the water is carrying sediment).If the coefficient of static friction (cs) is 0.35; the coefficient of drag is 2.1 (length of vehicle is perpendicular to flow); the velocity of flow, regardless of depth, is 5 ft/s; and the total vehicle weight is equally distributed to all tires. Given this

B.At what depth of flow does the vehicle begin to move?

Reference no: EM13542372

Questions Cloud

A magician pulls a tablecloth from under : A magician pulls a tablecloth from under a 200 g mug located 30.0 cm from the edge of the cloth. The cloth exerts a friction force of 0.140 N on the mug, and the cloth is pulled with a constant acceleration of 2.90 m/s2. How far does the mug move rel..
Air which may be treated as an ideal gas : Air which may be treated as an ideal gas, is compressed from 100 kpa to 1500 kpa in a quasisatatic manner so that it obeys the relation ....pV^1.3 = constant determine the amount of work necessary to compress 100kg of air. The initial temperature ..
Determine vb of the load b after it has dropped 200 mm : A 40 kg sheave a OF RADIUS R=350 mm. and cenral radiusof gyration k=250 mm carries a 160 kg load b and is suspended by a cable and a spring of modulus k=1.2 kN/m. if the system is relased from rest in the positon show the spring is stretched 100 mm d..
Determine the magnitude and location of the maximum bending : For the beam and loading shown, write the equation of he shear and bending-moment curves and determine the magnitude and location of the maximum bending moment
Distance from the roadway to the floor of the vehicle : You are in charge of evaluating the safety (hazard) of a low water crossing. Traffic surveys show that the "Aaverage"vehicle using the crossing is semi-rectangular in shape (10 ft long, 5 ft wide, and 4.0 ft high - not including the distance from the..
Determine the most economical design pipe size and number : Determine the most economical design (i.e. pipe size and number and location of pumps). Hint: Vary your pipe diameter and consider pumps in series.
Determine the velocity of the collar at point b for values : To imagine the diagram, the collar at point A (unstretched) is on the same x-axis as the anchor @ C, while the collar point B (stretched) is located downwards-left to point A, forming a 30 degree angle with the y-axis (vertical). In other words, the ..
Assigning the central pier and the abutment as fixed : Design a 300 + sl m long variable graded terrace for a land having an average slope of 2 %. Maximum permissible velocity of water in the terrace channel is 60 cm/sec. The most sever rainfall expected in 10 yr RI has an intensity of 9 cm/hr.
Determine the components of the reaction at point c when the : The object ABC consists of two slender rods welded together at point B. Rod AB has a mass of 1 kg and bar BC has a mass of 2 kg. Knowing the magnitude of the angular velocity of ABC

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  Determine what is the effluent concentration at the rate

A first order reaction occurs in a PFR at the rate of 2.1 hr^-1. The reactor volume is 1400L and flow is 15 gpm. If the influent concentration is 200 mg/L, then what is the effluent concentration

  Briefly describe the treatment necessary to produce

It is possible to produce cast irons that consist of a martensite matrix in which graphite is embedded in either flake, nodule, or rosette form. Briefly describe the treatment necessary to produce

  Design temperature and residence time have been established

The oven exhaust gases are available at 250 F. Assume that the design temperature and residence time have been established as 1300 F and 0.6 sec, respectively. The type of burner used in the process requires outside air at a moass ratio of 12:1

  Determine what is the maximum shear stress

A steel tube has an outside diameter of 2.5 inches and an inside diameter of 2.375 (1/8" thick). If it transmits 35 hp when turning at 2700 rpm, what is the maximum shear stress

  What should be the cross-sectional area of the circular rod

An engineer has to design a rod made with the same steel to carry a load of 150 kips without yielding. He desires to have a factor of safety against yielding of 1.5. What should be the cross-sectional area of the circular rod

  Determine the size of pipe for a water temperature

The difference in water level is 60ft. Determine the size of pipe for a water temperature of 60 degrees Fahrenheit. Apply The Darcy-Weisbach equation.

  Calculate the molar mass of the biomolecule

For carbon tetrachloride, the boiling point constant is 5.03°C · kg/mol, and the boiling point of pure carbon tetrachloride is 76.50°C.

  Calculate the surface area required for a stabilization pond

Calculate the surface area required for a stabilization pond to serve a domestic population of 1000. Assume 80 gpcd at 210 mg/l of BOD. Use a design loading of 20 lb of BOD/acre/day.

  How to determine the friction drag on one side of the plate

Water flows past a triangular flat plate oriented parallel to the free stream. Integrate the wall shear stress over the plate to determine the friction drag on one side of the plate. Assume laminar boundary layer flow.

  Determine what is the carts speed at point b

The cart takes 5.00s to go from point A to point C, and the cart takes 1.90s to go from point B to point C. What is the cart's speed at point B. Express answer numerically to three significant figures in feet per second.

  Compute the percent change n in the normal forces at a

During an engine test on the ground, a propeller thrust T = 4000 N is generated on the 1500 kg airplane with mass center at G. The main wheels at B are locked and do not skid; the small tail wheel at A has no brake.

  Determine the required shaker frequency to cause resonance

A floor slab has a fundamental bending frequency of 10Hz. A shaker is placed at the centre of the slab for a dynamic testing. The tests confirm that the slab displays a damping ratio of 2% of critical.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd