Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Discuss the advantages and disadvantages of each of the following methods for measuring (i) crack length and (ii) crack closure loads:
(a) Crack mouth opening displacement gage.
(b) Strain gages mounted in the wake of the crack, above and below the plane of the crack.
(c) Strain gages mounted immediately ahead of the crack tip.
(d) Back-face strain gage.
(e) DC electrical potential drop.
(f) AC electrical potential drop.
(g) Ultrasonics.
(h) Acoustic emission.
(i) Travelling microscope providing a direct optical image of the crack on the specimen surface.
Also discuss the experimental procedures you would use for the calibration of crack length and crack closure, where appropriate, for each of the above methods.
the stress at a point is shown on the element. Determine the principal stresses and the absolute maximum shear stress.
find an expression for the diameter, D, of the droplet, in terms of the specific weight and surface tension, assuming the contact angle just before seperating is zero.
A composite beam is made by attaching the timber and steel portions with bolts of 14-mm diameter spaced logitudinally every 200 mm. The modulous of elasticity is 10 GPa for the wood and 180 GPa for the steel.
A 9,000-lb single wheel load is placed on a PCC slab that is 9.5 in. thick. The concrete has a modulus of elasticity of 5 million psi with a Poisson's ratio of 0.15. The modulus of subgrade reaction is 225 pci.
The flow in the river is 30ft^3/min and the first-order rate constant for disinfection is 6min^-1. 1)What kind of hydrodynamic model should you use. 2) write the mass balance equation for microorganisms in symbols at steady state. define symbols.
During the following day the sun melts the ice cover. Determine the new depth if the flow rate remains the same and the surface roughness of the ice is essentially the same as that for the bottom and sides of the river.
determine the highest real root of f(x)= 0.95x^3 - 5.9x^2 +10.9x-6: (a)graphically. (b) using the newton raphson method(three iterations, xi= 3.5). (c) using the secant method(three iterations, xi-1= 2.5 and xi= 3.5).
If the outer ring rotates in the clockwise direction at 7 rpm and the inner ring rotates in the counterclockwise direction at 12 rpm, what is the angular velocity of the carriers and what is the velocity of C, the center of the top carrier.
The owner of a downtown parking lot has employed a civil engineering consulting frim to advise him on the economic feasibility of constructing an office building on the site. bill samuels, a newly hired civil engineer, has been assigned to make the a..
If this refrigerator is to operate in an environment at 30°C, what is the minimum pressure to which the refrigerant should be compressed? Why?
Design a circular radial-flow clarifier for a town with a projected population of 45,000. Assume that the wastewater flow is 400 L/capita-day. Size the system for a 2-hr
A flow of 4.8 m3/s is to be developed from a 500 km2 watershed. The reservoir is estimated to cover 1,700 ha. The annual rainfall is 97 cm, the annual runoff is 30 cm, and the annual evaporation is 120 cm
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd