Determine x the downstream position of the pitot tube

Assignment Help Civil Engineering
Reference no: EM13318332

Air at 20oC and 1atm flows at 20 m/s past the flat plate . A pitot tube placed 2mm from the wall, develops a manometer head h=16mm of Meriam red oil (SG = 0.827), measured relative to atmospheric pressure. Determine x, the downstream position of the pitot tube relative to the leading edge of the flat plate. (hint: assume laminar and determine the velocity at the manometer inlet)

Reference no: EM13318332

Questions Cloud

Discuss the tax treatment : Discuss the tax treatment that Bob may take with regard to this loan.
Find the terminal velocity of the big drop : 8 equal drops of water are falling through air with a steady velocity of 10 cm/s. then the terminal velocity of the big drop is
What is the molar mass at temperature of 22 degrees c : What is the molar mass if a 0.550-g sample occupies 258mL at a pressure of 744 torr and a temperature of 22 degrees C
Do you observe any trend-cycles or random variation : Plot above data on a graph. Do you observe any trend, cycles or random variation? Starting in year 4 and moving to year 12, forecast demand using a 3-year moving average. Plot your forecast on the same graph as the original data
Determine x the downstream position of the pitot tube : Air at 20oC and 1atm flows at 20 m/s past the flat plate . A pitot tube placed 2mm from the wall, develops a manometer head h=16mm of Meriam red oil (SG = 0.827), measured relative to atmospheric pressure.
Any allowance for future uncollectible accounts explain : Do you agree with Arnold's reasoning for not reporting any allowance for future uncollectible accounts? Explain.
Personal ethics development and ground rules : Paper on personal ethics development that examines your personal ethical system and ground rules, including it's origins and devlopment.
Calculate the equivalent overflow rate in gpd per ft squared : The settling velocity of alum floc is approximately 0.0014 fps in water at 10 degrees celsius. Calculate the equivalent overflow rate in gpd/ft squared. What is the minimum detention time in hours
Explain what is the ratio of the root mean square : The two isotopes of uranium, U-235 and U-238 can be separated by effusion of the corresponding UF6 gasses. What is the ratio of the root mean square speed 238-UF6 to that of 235-UF6

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine what is the uncertainty in meters in the distance

A laser range finder consists of a laser and a light receiver. It operates by bouncing a laser pulse off a mirror and measuring the time of flight, the time it takes for the pulse to leave the laser, bounce off the mirror and return to the receive..

  Determine water level rise in an unconfined aquifer produced

Determine the water level rise in an unconfined aquifer produced by a seasonal precipitation of four inches. The aquifers porosity is 20 percent and its specific retention is 9 percent.

  Determine the factor of safety for the joint at the theta

two wooden members of uniform rectangular cross section of sides a = 100 mm and b = 60 mm are joined by a simple glued joint as shown. knowing that the ultimate stress of the joint are 1.26 MPa in tension and 1.50 MPA in shear and that P= 6kN

  What flow rate of fresh water used to reduce concentrations

The new owners propose to flush the pond into their discharge pipe leading to the Atlantic Ocean, which has a salt concentration above 30,000 mg/L. What flow rate of fresh water (in m3/s) must they use to reduce the salt concentration

  How to calculate the forces in members ec and ef

Using method of joints, calculate the forces in members EC and EF. Note that the length of the member CD is 3.464 m, the length of member EC is 2m, and angle CDE is 30 degree ( this will cut down a bit of trigonometry effort).

  Which machine should be chosen using an interest rate

North City must choose between two new snow-removal machines. The SuperBlower has a $70,000 first cost, a 20 year life, and an $8000 salvage value. At the end of 9 years , it will need a major overhaul costing $19,000.

  What and where will be the maximum fluid pressure

A 10cm diameter vertical tank holds 20cm of water topped with 15cm of ethyl alcohol. The cylinder is rotated about its central axis at a rotation rate of 20 rad/s. (a) What will be the shape of the air-alcohol and alcohol-water interfaces

  What are the effects of water pollution on the components

What are the effects of water pollution on the components of the hydrologic cycle?

  Determine the components of the reaction at c

Knowing that P=109.2 kips and Q=72.8 kips, determine (a) the components of the reaction at C, (b) the components of the force exerted at B on segment AB.

  Determine what does the equation reduce to in steady flow

Define what each term in the equation means. Overall, what quantity is being conserved? Under what conditions might you be justified in assuming that non-linear terms are not important

  Determine the normal and shear stresses acting on an angle

A pressurized steel tank has a radius r=0.6m, a wall thickness t=18mm and an internal pressure p of 2.8 MPa.The steel has a modulus of elasticity E of 200 GP and a poissons ratio 0.30.

  What is the vapor pressure of carbon dioxide in the bottle

What is the vapor pressure of carbon dioxide in the bottle before it is opened (i.e., when it is at equilibrium) assuming no other ions are present besides those related to CO2 and water

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd