Determine where the groundwater divide is located

Assignment Help Civil Engineering
Reference no: EM13315740

In a water table aquifer bounded on the ends by rivers, the hydraulic conductivity is 50 m/day. The hydraulic heads at x = 0 and x = 1000 m are 100 m and 90 m, respectively.

(a) Calculate the darcy flux at x = 0, 100, 500 and 1000 m, and the flow rate per uit width of the aquifer. Assume recharge = 0

(b) Calculate the darcy flux at x = 0, 100, 500 and 1000 m, and the flow rate per unit width of the aquifer. Assume recharge = 0.02 m/day

(c) For (b), given the streams are located at x = 0 and x = 1000 m, determine where the groundwater divide is located.

Reference no: EM13315740

Questions Cloud

Advise nathan valid contract with dubious connections : Advise Nathan if there is a valid contract with Dubious Connections Pty Ltd, and any remedies that may be available to him.
Determine the estimated cost of a similar process unit : From historical cost records, the capacity ratio exponent of a process unit is 0.5. Use the capacity ratios raised to an exponent method to determine the estimated cost of a similar process unit with a capacity of 310 ft3/hr.
Find the separation between slits : A double slit experiment is performed with sodium(yellow) light of wavelength 589.3nm, Find the separation between slits
What is the discharge rate per unit width of the aquifer : To avoid the salinization of soil in a farming area, parallel drainage canals are to be installed to maintain the water table at a depth of at least 4m below the ground surface. It is thought that no evapo-transpiration would occur below that dept..
Determine where the groundwater divide is located : In a water table aquifer bounded on the ends by rivers, the hydraulic conductivity is 50 m/day. The hydraulic heads at x = 0 and x = 1000 m are 100 m and 90 m, respectively.
Develop an opinion as to the degree : As we noted in the lecture some educationalists are quick to point out that hypertext links facilitate memory and understanding and this has lead to encouragement of WWW use in the classroom.
Calculate the daily discharge per 1000 feet into the river : A canal was constructed running parallel to a river 1500 ft away. Both fully penetrate a sand aquifer with a hydraulic conductivity of 1.2 ft/d. The area is subject to rainfall of 1.8 ft/y and evaporation of 1.3 ft/y.
Find how much time elapses before you hear the sonic boom : A supersonic jet passes directly overhead at an altitude of 12,930 m, traveling at 680 m/s, or mach 2. How much time elapses before you hear the sonic boom
What is the rms amplitude of the ac voltage : A wind turbine turns an electrical generator that contains a wire coil with 36 loops and a loop area of 0.10 m2. what is the rms amplitude of the AC voltage produced by the generator

Reviews

Write a Review

Civil Engineering Questions & Answers

  Projectile shot vertically upward

The height (in meters) of a projectile shot vertically upward from a point 2 m above ground level with an initial velocity of 24.5 m/s is h2+24.5t-4.9t^2 after t seconds. a) When does the projectile reach its maximum height? b) What is the maximum..

  Determine the velocity of the solid sphere

A solid steel sphere with a specific gravity of 7.85 and diameter of 0.02 m is falling at its terminal velocity through water at 25 °C. Using either trial-and-error or a graphical approach, determine the velocity of the sphere

  Calculate the difference in elevation from a to b

In trigonometric leveling from point A to point B, the slope distance and the zenith angle measured in A were 2504.897 m and 85o08'54". At B, these measurements were 2504.891 m and 94o52'10" respectively.

  Calculate the bearing stress on the shaft key

A rotating shaft with an applied torque of 400 Newton-meters is held in place (stopped) by a shaft key. The diameter of the shaft is 15 centimeters. The shaft key has a length of 20 cm, and is square, with its width and height being 5 cm.

  Determine the cod

Determine the COD, carbonaceous BOD, and nitrogenous oxygen demand of a 100 mg/L solution of urea (N2H4CO)

  Identify the minimum and maximum deflection and rope tension

Friction of the walker's shoes and rope are sufficient to cause the rope to have more tension on one side then the other. Neglecting the weight and any elastic deformations of the 20.1-m long rope, create a table using 1.0m increment for the range

  What are magnitude and direction of the hydrostatic force

The top of the object is 1 m below the surface of the fluid. What are the magnitude and direction of the hydrostatic force acting on the top of the object.

  Determine what is the void ratio and the specific gravity

For a same soil, two moist densities and their corresponding degrees of saturation are given in the following table Density (kg/m^3) S(%) 1700 55 1800 70 What is the void ratio (e) and the specific gravity (Gs)?

  Determine the minimum footing length l of the columns

Assume a value of B, compute the allowable bearing capacity, then solve for B. Show at least 1 iteration with whatever assumed width irrespective of whether or not you get the desired Factor of safety.

  Travel of two particles problem

Two particles start from the same point along the same straight line and at the same instant. The first particle travels with a constant velocity v and the second with a constant acceleration.

  Estimate shaft elongation in millimeters with applied force

A 4.00-cm-diameter, 0.80-m long rod of aluminum 7075-T6 is subjected to an axial tensile force with a factor of safety of 1.75. The yield stress and modulus of elasticity of aluminum 7075-T6 are 500. MPa and 210. GPa, respectively.

  What is the first order approximation for the mean of y

Let X be a uniformly distributed continuous random variable ranging between 5 and 8, X ~ U[5 , 8]. Variable Y is a function of X: Y: h(X)= 2X^2+1 a. Determine the PDF of Y. b. Find the expected value of Y.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd