Determine when the crates begin to slide at an angle

Assignment Help Civil Engineering
Reference no: EM13313616

Crates A and B weigh 300 lb and 110 lb, respectively. They are connected together with a cable and placed on the inclined plane. If the angle θ is gradually increased, determine when the crates begin to slide. The coefficients of static friction between the crates and the plane are μA=0.25 and μB=0.40.

Reference no: EM13313616

Questions Cloud

A person chooses between leisure and consumption : A person chooses between leisure and consumption. The utility derived from any combination of leisure and consumption is given by the formula: u = LC - 88C where u is utility, L is the number of leisure hours per week, and C is the number of dolla..
Determine min horizontal force p required to hold the crate : Determine the minimum horizontal force P required to hold the crate from sliding down the plane. The crate has a mass of 70kg and the coefficient of static friction between the crate and the plane is μs = 0.45.
Calculate minimum force he must exert to get moving back : a contestant in a winter games event pushes a 31 kg block of ice across a frozen lake. the coefficient of static friction is 0.1, Calculate minimum Force he must exert to get moving back
Determine the commissions paid to specific employees of sale : Design a query that will allow the finance department to determine the commissions paid to specific employees of the sales department for the month of December.
Determine when the crates begin to slide at an angle : Crates A and B weigh 300 lb and 110 lb, respectively. They are connected together with a cable and placed on the inclined plane. If the angle θ is gradually increased, determine when the crates begin to slide.
What is the linear speed of a point on its edge : a grindstone has a radius of 6.00 cm and rotates at 7000 rpm. What is the linear speed of a point on its edge
Determine the inclination theta of the ladder : Determine the inclination θ of the ladder if the coefficient of static friction between the friction pad A and the ground is μs= 0.3. Assume the wall at B is smooth. The center of gravity for the man is at G.
What is the difference in air pressures : Hurricane winds of 95 m/h are blowing over the flat roof of a well sealed house. What is the difference in air pressure between the inside and outside of the house
Determine all components at the reactions at the pin support : The compound beam assembly shown is made up of 4 members connected by pins and is supported by hinges/pins at A and E. L= 2.6m (L is the lengthD to E) , and w= 60 (w is the load-lines) .

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the maximum shear stress in the material

An element of aluminium in a form of a rectangular parallel pipe has a length 'a' along the x axis of 5.5 in, a length 'b' on the y axis of 4.5 in. Determine the maximum shear stress in the material,the change in length.

  What is temperature of the tires of the increase pressure

A motorists inflates the tires of her car to a gauge pressure of 180 kilopascals on a day when the temperature is -8.0 degrees Celsius. When she arrives at her destination, the tire gauge pressure has increased to 245 kilopascals.

  Estimate low-dose cancer risk from occupational inhalation

the recommended threshhold limit value ( TLV-ACGIH) air concentration for occupational exposure to water-insoluble hexavalent chromium Cr (VI) is 0.01 mg/M^3. this concentration is based on an assumption that the individual is generally healthy an..

  Find what is the builder capitalized cost to const the plant

A home builder must construct a sewage treatment plant and deposit sufficient money in a perpetual trust fund to pay the $5000 per year operating cost and to replace the treatment plant every 40 years.

  Determine the lengths of dg and cb of triangular tract

ABC is a triangular tract of land. The 1.5 tract DEFG is to be subdivided. AE is 480ft and DC is 350 ft. Determine the lengths of DG and CB. (Note 1 acre= 43,560 f^2)

  How far apart must two 18 m diameter tanks be placed

How far apart must two 18 m diameter tanks be placed such that their stress overlap is not greater than 10% of the contact stress at depths of 10, 20, and 30 m

  Determine the time in seconds to obtain a density

The salt water mixes thoroughly with the fresh water and the mixture overflows out of the tank. If the flow rate out of the tank is 60 liters/minute. Assume freshwater is 1000 kg/m^3, and the salty water is 1020 kg/m^3.

  Determine from first principles

At a section in a beam the tensile stress due to bending is 70 N/mm2 and there is a shear stress of 25 N/mm2. Determine from first principles, the magnitude and direction of the principal stresses

  What is result of volume change in saturated cohesive oil

What is the result of a volume change in a saturated cohesive soil because of expulsion of the water occupying the void spaces

  Determine what is the air flow in cubic meters per hour

The blower on an air conditioning unit produces 80 cubic feet per minute of air in the ductwork. What is the air flow in cubic meters per hour

  Determine the deflection in degree for horizontal wind speed

Determine the deflection in degrees for horizontal wind speed of 10m/s and what is the magnitude of the force required at the bottom of the sign to prevent the sign from deflecting

  Calculate air velocity and mass flow rate through the slit

the room described in problem 8.1 gas a 1 m wude door with a 1 cm high slit at the floor level. THe oil spill has a rectagular area of sides 0.5 m by 0.5 m. (a) calculate the pressure increase, the air velocity, and the mass flow rate throug the sl..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd