Determine what is the resulting solids concentration

Assignment Help Civil Engineering
Reference no: EM13304851

Raw primary sludge at a solids concentration of 4% is mixed with waste activated sludge at a solids concentration of 0.5%. The flows are 20 and 24 gal/min, respectively. What is the resulting solids concentration? This mixture is thickened to a solids concentration? This mix of 8% solids. What are the quantities (in gallons per minute) of the thickened sludge and thickener overflow (water) produced? Assume perfect solids capture in the thickener.

Reference no: EM13304851

Questions Cloud

How large should wei dividend payout ratio be next year : According to the residual distribution model (assuming all payments are in the form of dividends), how large should Wei's dividend payout ratio be next year?
Determine how much oil is recovered by the weight : A separator accepts waste oil at 70% oil and 30% water by weight. The top product stream is pure oil while the bottom underflow contains 10% oil. If a flow of 20 gal/min is fed to the tank, how much oil is recovered
Estimate the value of the option to develop the property : estimate the value of the option to develop the property.(hint:Make any assumptions you must to arrive at an estimate)
What is the size of the circle of light : A flat stack of two materials, the first of index of refraction 1.52 and thickness 2 mm, and the second of index of refraction 1.63, What is the size (radius) of the circle of light
Determine what is the resulting solids concentration : Raw primary sludge at a solids concentration of 4% is mixed with waste activated sludge at a solids concentration of 0.5%. The flows are 20 and 24 gal/min, respectively. What is the resulting solids concentration
Find v and q by hazen-williams for a new cast iron pipe : The 12 in diameter cast iron pipe is 2000ft long, the water surface is El 200 in the reservoir on the left B. El 175 on the right. A. Find V and Q by hazen-williams for a new cast iron pipe (Chw=130) Neglect entrance, exit and local losses.
Which resistor consumes the least power : Resistors of values 8, 12 and 24 Ohms are connected in parallel across a fresh battery with voltage 12 volts. Which resistor consumes the least power
Determine the maximum compression of the spring : The 30-Mg freight car A and 15-Mg freight car B are moving toward each other with the velocities VA= 20 km/h to the right and VB= 10 km/h to the left. the spring constant on car A is k= 3MN/m.
Calculate its velocity from general kinetic energy equation : If the kinetic energy of an electron is 910 eV, calculate its De Broglie wavelength. For this non-relativistic electron you must firs, calculate its velocity from the general kinetic energy equation

Reviews

Write a Review

Civil Engineering Questions & Answers

  Formulate a linear program for blend mix

Formulate a Linear Program for Blend Mix at Bluegrass Distillery, The Bluegrass Distillery produces custom-blended whiskey

  Assist structural engineer for a bridge replacement project

You should provide the structural engineer with a formal typed report that will include all of your analyses and final size of the footing. You should also include all of your design assumptions in your report.

  How much heat must be supplied to maintain desired temp

A small building that shelters a water supply pump measures 2 m x 3 m x 2.4 m high. It is constructed of 1- cm thick wood having a thermal conductivity of 0.126 W*m^-1*K^-1.

  How much will each leg shorten under the applied

given that E for the tube material is 70 GN/m2 and the stool legs are 75cm long, how much will each leg shorten under the applied compressive load (take g = 9.8m/s2)

  Determine the tension in cables ac and ab

The casting has a mass of 3Mg. Suspended in a vertical position and initially at rest, it ia given an upward speed of 200mm/s in o.s^s using a crane hook H. Determine the tension in cables AC and AB during this time interval if acceleration is con..

  What are the speed and acceleration of the disks top

disk of radius R=7 in. spins at a constant angular speed of w=500rpm in the clockwise direction. If the disk is released from rest far above the ground, what are the speed and acceleration of the disk's top C point after it has fallen h=3ft

  How much larger should street name be in order to be legible

street nam sizes on the signs at a certain location can be discerned by a person with 20/40 vision from a distance of 300 ft. how much larger should the street names be in order to be legible to a person with 20/50 vision from a distnace of 450 ..

  Determine station of pvc and pvt and design speed of curve

An equal-tangent crest vertical curve connects a +3.2% and -1.1% grade. The PVI is at station 98+20. Due to drainage considerations, the highest point of the curve is at station 100+79.35.

  Compute the max acceptable tensile service load for angle

The service live load is three times the dead load. The 4-in leg contains a single line of 7/8 inch diameter bolts, and the 6 inch leg contains a double gage line of 7/8 inch diameter bolts.

  Calculate the relative compaction

A dam project specifies 97% compaction. Lab tests on the soil being used indicate that it has a maximum dry density of 1900 kg/m3 at an optimum water content of 13.2%. Field tests give the following results: Field dry density is 1790 kg/m3 and 16...

  Compute the seepage velocity

Compute the seepage velocity and estimate the hydraulic gradient in the aquifer if the porosity of the soil is 42%.

  Determine the distance the engine is hoisted

The 3.5-Mg engine is suspended from a spreader beam having a negligible mass and is hoisted by a crane which exerts a force of 40 kN on the hoisting cable. Determine the distance the engine is hoisted in 2.4 s, starting from rest.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd