Determine what is the resultant thermal energy

Assignment Help Civil Engineering
Reference no: EM13305199

The specific heat (C sub p) of aluminum is 0.214 calories per gram degrees Celsius (0.214 cal/g-C). If a cube of aluminum with a mass of 13.6 kg exhibits a change in temperature of +30 degrees Celsuis, what is the resultant thermal energy?

Reference no: EM13305199

Questions Cloud

Committee concerning the current income tax regulations : What would be your response to the Committee concerning the current Income Tax Regulations?
How would you hedge that risk : Assuming that interest rate risk is the only risk of concern, will the hedge described above be effective? Why or why not? Is there any other risk that deserves to be considered? If so, how would you hedge that risk?
Whats is the minimum possible surface area of the object : A fully enclosed cylindrical fuel tank with a diameter of 6.00 meters and a height of 8.00 meters has a manufacturing tolerance of +/- 0.04 meteres for each of these dimensions.
Determine where will an object at infinity be focused : A diverging lens with f = -31.5 cm is placed 11 cm behind a converging lens with f = 24 cm. Where will an object at infinity be focused
Determine what is the resultant thermal energy : The specific heat (C sub p) of aluminum is 0.214 calories per gram degrees Celsius (0.214 cal/g-C). If a cube of aluminum with a mass of 13.6 kg exhibits a change in temperature of +30 degrees Celsuis, what is the resultant thermal energy
Compute the focal length of the diverging lens : A 33.4 cm focal-length converging lens is 24.8 cm behind a diverging lens. Parallel light strikes the diverging lens. What is the focal length of the diverging lens
The issues with auditing these relationships : What are the issues with auditing these relationships?
Determine how much power will be required above sea level : If I raise a 1000 lbf weight 100 feet above sea level on earth in 10 seconds how much power will be required
Determine the index of refraction of the lens material : Both surfaces of a double convex lens have radii of 30.0 cm. what is the index of refraction of the lens material

Reviews

Write a Review

Civil Engineering Questions & Answers

  Derive eq for reaction force associated with conversation

Derive an equation for the reaction force (Rx) associated with conservation of momentum in a straight length of pipe of uniform diameter. Approximate the velocity as steady and uniform at each cross-section, and the fluid as constant density.

  What ventilation rate is needed to maintain formaldehyde

Indoor air quality is an under appreciated health hazardous. The air quality in a building can be modeled as a CSTR. Suppose that the carpet in a new office building releases formaldehyde at a rate of 10 micrograms per hour.

  Embankment for a highway

An embankment for a highway 30m wide & 1.5m in a compacted thickness is to be constructed from a sandy trucked from a borrow pit. the water contenet of the sandy soil in the borrow pit is 15%& its void ratio is 0.69.

  Calculate the amplitude of vertical motion of the machine

A machine is supported on four steel springs for which damping can be neglected. The natural frequency of vertical vibration of the machine-spring system is 200 cycles per minute. The machine generates a vertical force p(t)=p0sinwt.

  Determine what external force is required to hold the bend

A pipe 1ft in diameter bends through an angle of 135 degrees. The velocity of flow of gasoline ( S = 0.8) is 20ft/s and the pressure is 10psig in the bend. What external force is required to hold the bend against the action of the gasoline

  Determine what percentage of the time will the through lane

A traffic engineer is trying to design a left turn bay on an EB approach to an intersection. The signal timing for left turns will have 10 seconds of "left turn only" green time and 50 seconds of red time each signal cycle.

  Maximum and minimum stress intensities in the section

Determine the maximum and minimum stress intensities in the section.

  What is elastic wave tomography

what is elastic wave tomography , flat jack, push shear test in masonary?

  Find the value of the kinetic energy correction coefficient

assuming that the velocity variation within the main channel and the floodplain subsections is much smaller than the change in mean velocities between subsections, find the value of the kinetic energy correction coefficient.

  Determine the final temperature of the water

A piston-cylinder device contains 0.2kg of water initially at 800 kPa and 0.06m^3. Now 200 kJ of heat is transferred to the water while its pressure is held constant. Determine the final temperature of the water.

  Determine longitudinal and hoop stresses in the copper pipe

Typical water supply at a faucet in any building is conveyed in copper pipe that is ½" in inside diameter, with a wall thickness of 0.040". If the water pressure is 50 psi and the valve is closed (meaning that water is not flowing)

  Determine the speed of both cars just after coupling

the 15,000 kg boxcar A is coasting freely at 1.5 m/s on the horizontal track when it encounters a tank car B having a mass of 12,000 kg and coasting at 0.75 m/s toward it. If the cars meet and couple together

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd