Determine what is the pressure acting on the sand

Assignment Help Civil Engineering
Reference no: EM13296430

A 3-ft diameter column with weight of 150 kg is placed on top of 1 m thick aggregate layer. The soil beneath the aggregate layer is sand. The friction angle of the aggregate is 36 degrees and the unit weight is 22 lb/ft3. What is the pressure acting on the sand?

Reference no: EM13296430

Questions Cloud

Describe the measurements that would have to be taken : describe the measurements that would have to be taken and the equations that would have to be used to determine G23, V32, and E2 for a specially orthotropic transversely isotropic material from a single tensile test.
Explain the pkb values for the dibasic base b are pkb1 : The pKb values for the dibasic base B are pKb1 = 2.1 and pKb2 = 7.8. Calculate the pH at each of the following points in the titration of 50.0 mL of a 0.60 M B(aq) with 0.60 M HCl(aq).
What is the market-to-book ratio : ABC's Balance Sheet lists Current Assets of $300, Current Liabilities of $200, Fixed Assets of $700, Long-Term Debt of $400. ABC has 200 shares outstanding. What is the market-to-book ratio (MTB) if the market price per share is $8?
Under the revised uniform partnership act : Under the Revised Uniform Partnership Act, The difference between a limited partnership and a registered limited liability partnership (RLLP) is that
Determine what is the pressure acting on the sand : A 3-ft diameter column with weight of 150 kg is placed on top of 1 m thick aggregate layer. The soil beneath the aggregate layer is sand. The friction angle of the aggregate is 36 degrees and the unit weight is 22 lb/ft3. What is the pressure acti..
Which company would a lender prefer to work with : Company XYZ has $700,000 in total assets, one third have been financed by equity and two thirds which have been financed by dept. Based on their dept-to equity ratios, which company would a lender prefer to work with?
Explain a born-haber cycle for the formation of nacl : The Born-Haber cycle is a series of steps that represent the formation of an ionic compound from a metal and a nonmetal. For example, the steps in a Born-Haber cycle for the formation of NaCl(s) consist of sublimation of the metal Na atom
Determine maximum speed of the free fall for the sky driver : A sky diver with a mass of 75 kg jumps from an aircraft. The aerodynamic drag force acting on the sky diver is known to be Fd = kV^2, where k = 0.228. Determine the maximum speed of the free fall for the sky diver and the speed reached after 100 m..
Discussing the different sources of environmental variation : When breeders make selections they do so based on the phenotypes of plants they are comparing. Write a half page discussing the different sources of environmental variation that can influence the phenotype a breeder will observe

Reviews

Write a Review

Civil Engineering Questions & Answers

  Density of traffic stream in lane

Assume you are observing traffic in a single lane of a highway at a specific location. you measure the average headway and average spacing of passing vehicles as 3 seconds and 150 ft, respectively. calculate the flow, average speed, and density of..

  Calculate the volume of gas produced

A 1-kg block of dry ice(solid CO2) becomes a gas at room temperature. calculate the volume of gas produced at 25 degrees celsius and 975 kPa.

  Find the conductive heat loss through the furnace wall

Assuming unit surface area, find the conductive heat loss through the furnace wall and the temperature at the interface of the fire clay and red brick.

  Determine the resulting couple moment

Calculate the moments M_A and M_B about point A for the forces applied at points A and B. Then, determine the resulting couple moment M_R. Assume that a positive moment produces a counterclockwise rotation whereas a negative moment produces a cloc..

  Falling-head permeability test

A falling-head permeability test was carried out on a clay soil of diameter 100 mm and length 150 mm. In 4 minutes the head in the standpipe of diameter 5mm dropped from 680 to 350 mm.

  Determining a maximum safe speed

The central angle is 35 degrees, the superelevation is 0.08, and 20.6 ft is cleared (for sight distance) from the inside edge of the innermost lane. Determine a maximum safe speed (assuming current design standards) to the nearest 5 mi/h.

  Velocity profile from the pipe wall

Compute points on the velocity profile from the pipe wall to the centerline of a 3/4-in Type K copper tube if the volume flow rate of water at 60 degrees F is .50 gal/min.

  What is elastic wave tomography

what is elastic wave tomography , flat jack, push shear test in masonary?

  Calculate the numbers of married men, single men

calculate the numbers of married men, single men, married women and single women. Print these numbers on a student summary report. If any single men are over 30 years of age, print their names and ages on a separate eligible bachelors report.

  Determine the distance the engine is hoisted

The 3.5-Mg engine is suspended from a spreader beam having a negligible mass and is hoisted by a crane which exerts a force of 40 kN on the hoisting cable. Determine the distance the engine is hoisted in 2.4 s, starting from rest.

  Determine the constants sigma0 and k in the hall petch

determine the constants sigma0 and k in the Hall petch equation of 70-30 brass sample.

  Determining maximum acceleration and maximum velocity

The posItIon of a particle along a straight line is given by s = (t 3 - 9t 2 + 1St) ft, where t is in seconds. Determine its maximum acceleration and maximum velocity during the time interval 0 :5: t :5: 10 s.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd