Determine what is the power delivered to the fluid

Assignment Help Civil Engineering
Reference no: EM13308532

Water enters and leaves a pump in pipelines of the same diameter and approximately the same elevation. If the pressure on the inlet side of the pump is 30 kPa and a pressure of 500 kPa is desired for the water leaving the pump, what is the head that must be added by the pump, and what is the power delivered to the fluid?

Reference no: EM13308532

Questions Cloud

Determine final height of the fill after compaction : A 2 m high sandy fill material was placed loosely at a relative density of 47%. Laboratory studies indicated tht the maximum and minimum void ratios of the fill material are 0.92 and 0.53, respectively.
Which will offer downward component of force as piston rises : Consider a piston/cylinder arrangement that has a linear spring mounted such that as the piston rises to a certain point it will encounter the spring, which will offer a downward component of force as the piston rises further.
Find the final temperature using the three methods noted : It is desired to compare the results of property predictions for water near or in the saturation region using (a) the ideal gas equation, (b) the compressibility chart and (c) the steam tables.
What is meant by multi-modal biometrics for access control : What is meant by "Multi-modal Biometrics" for access control. In theory and in practice, what quantifiable advantages and disadvantages can be attributed to multi-modal biometrics
Determine what is the power delivered to the fluid : Water enters and leaves a pump in pipelines of the same diameter and approximately the same elevation. If the pressure on the inlet side of the pump is 30 kPa and a pressure of 500 kPa is desired for the water leaving the pump
Compare japan competitor and a u.s. competitor product : Firm has contacted you to participate in a focus group. The focus group will compare a Japan competitor product (J) and a U.S. competitor product (U) against China firm's product - compare a Japan competitor product (J) and a U.S. competitor produc..
Find liquid to be used in towing tank that allows reynolds : A 1:40 scale model of a ship is tested in a towing tank. Prototype operates in seawater at 60 F. Find a liquid to be used in the towing tank that allows both Froude and Reynolds scaling for the model and the prototype.
Determine the secondary voltage and current : A transformer has 100 turns in its primary windings and 500 turns in its secondary winding. calculate the secondary voltage and current
Introduction about outsourcing : Introduction about outsourcing

Reviews

Write a Review

Civil Engineering Questions & Answers

  Find the degree of saturation of the sandy soil in situ

an embankment for a highway 30m wide & 1.5m in a compacted thickness is to be constructed from a sandy trucked from a borrow pit.

  Design a horizontal curve with a 40-degree central angle

Design a horizontal curve with a 40-degree central angle (delta=40) for a two-lane road with 11-ft lanes. The design speed is 70 mi/h and superelevation is limited to 0.06ft/ft. Give radius, degree of curvature, and length of curve.

  What height difference is needed to generate the flow

A siphone generates a flow of 1 ft/sec thru a 1 inch OD, 3/4 ID hose. A) What height difference is needed to generate this flow B) What height for 10 ft/sec C) What for 100 ft/sec

  Does our non-destructive test have the required sensitivity

To be sure that the part does not fail, we plan to ensure that the maximum applied stress is only one third of the tensile strength. We use a non-destructive test that will detect any internal flaws greater than 1.25 mm long.

  Calculate the apparent porosities if the matrix is quartz

The dry weight of a core is 28.20 gm. When saturated with a brine having a density of 1.15 gm/cc, the weight increases to 31.50 gm. Calculate the apparent porosities if the matrix is 1) quartz or 2) calcite.

  Explain break even stripping ratio

Break Even Stripping Ratio (BESR), Given an underground total mining cost of $8.85 per tonne, surface mining costs of $2.95 per tonne of ore, and surface mining stripping costs of $1.75 per tonne of waste

  Determine the angle that vo forms with vertical by rocket

If the rocket's decent parachute does not deploy and the rocket lands 340 ft from A, determine the angle (alpha) that vo forms with the vertical, the maximum height h reached by the rocket, and the duration of the flight.

  What is value of combined detention and interception storage

During a 108 minute long storm, the precipitation rate over a 100 acre area is 1.65 in/hr. The phi index is 0.42 in/hr. The average outflow from the area is 92 cfs during the storm. What is the value of combined detention and interception storages ..

  Determine the downstream water level to produce the flowrate

The flow through an 8 ft. Parshall Flume is 129 cfs when Ha is 2.50 ft. Determine the downstream water level (Hb) that would produce this flowrate.

  Determine the unit strain developed in the concrete

a concrete test cylinder is loaded with p= 100k (445 kn) and resulting shortening of 0.036" (0.0914 mm). determine the unit strain developed in the concrete.

  What would the alkalinity be in terms of nacl equivalents

If the HCO3- alkalinity of a sample was 50 mg/l as CaC03, what would its alkalinity be in terms of NaCl equivalents

  Calculate the force

Calculate the force (in Kn) a punch press must exert if it is to punch out a large washer from a strip of 5-mm thick sheet steel with an ultimate shear strength of 400 MPa. The washer dimensions are as follows: hole diameter is 27 mm. outside diam..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd