Determine what is the magnitude of the load p

Assignment Help Civil Engineering
Reference no: EM13302842

A round bar of 6mm diameter is made of 6061-T6 aluminum. When the bar is stretched by an axial force P, its diameter decreases by 0.450 microns. what is the magnitude of the load P?

Reference no: EM13302842

Questions Cloud

What is the cost of the loan : What is the cost of the loan, and how much would you ask for as the loan amount if you had to have $1,000,000?
Determine force required to drag a small barge in canal : Determine the force required to drag a small barge (10 ft by 30 ft) in a shallow canal (3 inches deep) in order to maintain a velocity of 5 ft/sec. Assume that the fluid is behaving in a Newtonian fashion and the water temperature is 68 degree fah..
What is the most expensive car you could afford : You have saved $5,000 for a down payment on a new car. The largest monthly payment you can afford is $350. The loan would have a 10% APR (with interest compounded monthly) based on end-of-month payments.
Explain how to convert c program to mips program : Convert the following C program to MIPS program. Assuming that i, j, k, f, are stored in registers $s0, $s1, $s2, $s3 already.
Determine what is the magnitude of the load p : A round bar of 6mm diameter is made of 6061-T6 aluminum. When the bar is stretched by an axial force P, its diameter decreases by 0.450 microns. what is the magnitude of the load P
Two international organized crime groups : Compare and contrast at least two international organized crime groups with regard to their membership, operational methods, operational focus, and geographic area of operations.
Find invert of stilling basin require to form hydraulic jump : The subcritical water level in the channel downstream from the stilling basin is at an elevation of 100 feet above the datum. assume no energy loss over the spillway, determine the invert of the stilling basin required to form a hydraulic jump in ..
Find the new angular speed of the system : A potter's wheel (a solid, uniform disk) of mass 6.0kg and radius 25cm spins about its central axis with an angular speed of the wheel is 15rpm. Find the new angular speed of the system
Determine problems at evco''s current system : Analyse the data collected to determine problems at Evco's current system, and the nature of the problems. You must write a report on analysis of the existing system's problems.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Mixed liquor volatile suspended solids

For a mixed liquor volatile suspended solids (MLVSS) of 1800 mg/L, what is the total return solids flow rate?

  Find wavelength-celerity and group celerity in deep water

Offshore in deep water, a wave gage measures the height and period of a train of waves to be 2m and 7.5 s respectively. The wave train propagates toward the shore in a normal direction without refracting and the nearshore bottom slope is 1:40.

  Factor of safety with respect to tensile failure

The maximum gage pressure is known to be 8MPa in a spherical steel pressure vessel having a 250mm diameter and a 6mm wall thickness. Knowing that the ultimate stress in the steel used is (sigma u)= 400MPa, determine the factor of safety with respe..

  Determine the vertical distance climbed

Neglecting the effect of altitude of local gravitional acceleration, determine the vertical distance climbed. Assume an average air density of 1.18 kg/m^3.

  Plot the data as a graph on log log paper showing the volume

The volume of a sphere is V=4/3pir^3. Prepare a table of volume versus radius which allows the radius to vary from 2.0 to 10.0 cm in 1 cm increments. Plot the data as a graph on log log paper showing the volume to radius relation

  What is the uniform deterministic arrival rate

what is the uniform deterministic arrival rate if the vehicle queue is cleared in 35 minutes after vehicles begin to arrive (in veh/min.)?

  What is the annual crash rate for section of college street

Over the past 3 years, there have been 14, 13, and 15 crashes on this section of College Street. The two-way ADT on this section is 16,474 vehicles per day. What is the annual crash rate for this section of College Street

  Determine what the height should be to force to be critical

Given that uniform flow is subcrital and there is a weir in a rectangular channel, how do you determine what the weir height should be to force the flow to be critical. Draw this transition on a specific energy curve.

  Find the load p and stress in the aluminum for the stress

The column is composed of two materials, the inner is brass with a diameter of 100mm and the outer is aluminum with a diameter of 150mm. A rigid flat plate is placed on top to insure that both materials move together when compressed.

  Determine what is the total resistance of the loads

You have 4 resistors (loads) in parallel. What is the total resistance of those loads The loads are as follows 4ohms, 6ohms, 16ohms and 1 ohms. When calculating 1/R, round to the fourth decimal point. Percentage of error margin is 0.5

  Calculate the volume of a cylinder that contains 60 lbm

Calculate the volume of a cylinder that contains 60 lbm of carbon dioxide at 230°F and 23 psig pressure. Assume atmospheric pressure to be 14.7 psia.^4

  How much force must be applied to keep the gate \

A gate (shaped like .25 of a cylinder with radius R=3m) is used to control the flow of water through a canal.The height of the water in the tank is 30m. How much force must be applied to keep the gate from opening? The gate is 30m wide.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd