Determine what is the flexural strength of the rod

Assignment Help Civil Engineering
Reference no: EM13314009

A 3-point bending test is performed on a 10 mm diameter rod of Silicon Carbide. The distance between the supports is one foot. If the load at fracture is 10,000N, what is the flexural strength of the rod? How much bending (deflection) did the rod undergo just before failure?

Reference no: EM13314009

Questions Cloud

What is the volume of the paint : A partly-full paint can has 0.79 U.S. gallons of paint left in it. What is the volume of the paint and how thick is the layer of wet paint
Determine the slope angle at which failure would occur : A cutting 9 m deep is to be excavated in saturated clay of unit weight 19 kN/m3. The design shear strength parameters are cu = 30 kN/ m2 and fu = 0. A hard stratum underlies the clay at a depth of 11 m below ground level.
Estimate the probability that the electron passes : Two nanowires are separated by 1.0 nm as measured by STM. Inside the wires the potential energy is zero, Estimate the probability that the electron passes from one wire to the other
What is the net force acting on the car : A car changes it speed from rest to 12 km/hr in 4sec .If the mass of the car is 2000 killograms what is the net force acting on the car
Determine what is the flexural strength of the rod : A 3-point bending test is performed on a 10 mm diameter rod of Silicon Carbide. The distance between the supports is one foot. If the load at fracture is 10,000N, what is the flexural strength of the rod
Compute the total pressure if the volume of the reaction : Calculate the total pressure if the volume of the reaction container is then (i) doubled; or (ii) reduced 7-fold.
Determine probability that at least 7 will ride in carpools : suppose 76% of all commuters ride to work in carpools. if eight workers are randomly selected, find the probability that at least 7 will ride in carpools
Calcualte the percentage difference between the two speeds : A 75 kg skater, starts at 6m above the ground, potential energy =0 at 2m above the ground. Calcualte the percentage difference between the two speeds
Determine max pressure at bottom of gate 2 : Find max pressure at bottom of gate (psi) 2. Total horizontal force on gate 3. moment about the bottom of the gate

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  Which pipe would be suggested to the axis chemical company

Axis Chemical Company needs you to design a gravity sewer to convey 1,750 GPM of toxic waste. The pipe is to be glass-lined reinforced concrete (n = 0.009). Which pipe would you suggest the Joker use

  How to find the information in the visitors guide

On your first trip to Planet X you happen to take along a 165 g mass, a 40 cm long spring, a meter stick, and a stopwatch. You're curious about the free-fall acceleration on Planet X, where ordinary tasks seem easier than on earth

  What fraction of the herbicide is adsorbed

The herbicide 2,4,D, is applied to a golf course at a rate of 1.2 kg/ha. The organic matter content of the soil is 1%, bulk density is 1.3 g/cm3, and water content is 0.3.

  Calculate the time required for the particle

A 10 m diameter particle of unit density falls through air starting from rest. calculate the time required for the particle to attain 70% of the final terminal speed and the distance traveled by the particle during the time.

  Calculate by what factor the mass of propane has increased

A typical propane tank that we use for barbeque initially contains a pressure of 10 psi. The pressure is low, so we take it to the local store to fill the tank with more propane. After filling,the pressure is 100 psi.

  Define civil and environmental engineering

Civil and Environmental Engineering Question, 1. How is the problem of technology choice related to process selection and product design?

  Determine the ph of solution if an equivalent amount of naoh

A solution contains 300 mg/L of acetic acid. Determine the pH of the solution if an equivalent amount of sodium hydroxide (NaOH) is added to it. Determine the concentration of NaOH required (in mg/L).

  Find the steady-state concentration of pollutant

The pollutant has a reaction rate coeeficient k of 0.25/day. Assuming is pollutant is well mixed in the lake, find the steady-state concentration of pollutant in the lake.

  Determine maximum allowable compressive force can be applied

The force is applied at the two pins. The pins allow rotation around the z-axis and do not allow rotation around the y-axis. The length of the beam between the pins is 8m. Determine the maximum allowable compressive force that can be applied.

  Estimate the constant rate of withdrawal from reservoir

Estimate the constant rate of withdrawal (in m^3/s) from a 1375 ha reservoir in a month of 30 days during which the reservoir level dropped by 0.75 m in spite of an average inflow into the reservoir of 0.5 Mm^3/day.

  Find how many of the 15 access points must be blocked

A four- lane undivided multilane highway ( two lanes in each direction) has 11- ft lanes and 5- ft shoulders. At one point along the highway there is a 4% upgrade that is 0.62 mi long. There are 15 access points along this grade.

  Determine the magnitude of the total acceleration at time t

Knowing that its speed continues to increase at the same rate until it reaches 100 km/h at point C, 1) determine the speed at point B, and 2) the magnitude of the total acceleration when t = 20 seconds.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd