Determine what force is required to pull the shells apart

Assignment Help Civil Engineering
Reference no: EM13303463

Two hemispheric shells are perfectly sealed together, and the internal pressure is reduced to 43 % of atmospheric pressure. The inner radius is 10.5 cm, and the outer radius is 10.75 cm. The seal is located halfway between the inner and outer radius. If the atmospheric pressure is 101.3 kPa, what force is required to pull the shells apart?

Reference no: EM13303463

Questions Cloud

Discuss three forces of the globalization : Discuss three forces of theglobalization
What is the maximum constant amount she can withdrawal : Whats the maximum constant amount she can withdrawal for each of the remaining 28 yrs. starting in 2033 if the interest rate remains at a true 6%.
Explain the different types of interactive environments : Describe the differences in developing user interfaces for different application environments. Compare and contrast the different types of interactive environments.
Newspaper or business magazine that interesting : Blogs are in response to a periodical like a newspaper or business magazine that you find interesting .Answer 2 questions: 1) Why did you choose this article, what does it have to do with OB?
Determine what force is required to pull the shells apart : Two hemispheric shells are perfectly sealed together, and the internal pressure is reduced to 43 % of atmospheric pressure. The inner radius is 10.5 cm, and the outer radius is 10.75 cm. The seal is located halfway between the inner and outer radi..
How long will you wait from now : You expect to receive $11,000 at graduation in two years. You plan on investing at 12 percent until you have $97,000. How long will you wait from now? (Do not round the intermediate calculations)? 17.21 years, 23.75 years, 23.33 years, 21.21 years..
What is the average force exerted on the door : A machine gun fires 23 g bullets horizontally at 260 m/s at a constant rate of 30 bullets/s. what is the average force exerted on the door
Find how long until the concentration of fluoride is reduced : During a snowstorm the fluoride feeder in North Bend runs out of feeder solution. The rapid mix tank is connected to a 5-km long distribution pipe. The flow rate into the rapid mix tank is 0.44m^3/sec, and the volume of the tank is 2.50 m^3.
The legalization of previously illegal activities : Which, if any, of the following changes is likely to cause reported GDP (real and nominal) to increase when, in fact, total economic production is little changed?

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the rotation angle of end b relative to end a

If a torque of T = 1,100 N-m is applied to the composite assembly, determine: (a) the maximum shear stress in the aluminum tube and in the steel core. (b) the rotation angle of end B relative to end A.

  Find discharge flowing over a rectangular sharp crested wire

Find the discharge flowing over a rectangular sharp crested wire, in GPM, which has a width of 9.9 feet and a discharge coefficient of 3.24, if the head above the crest is 1.74 feet.

  Predict the temperature required in an isothermal plug flow

Using the method of Lee et al., predict the temperature required in an isothermal plug flow incinerator to reduce the xylene level in a waste gas from 100 ppm to 10 ppm. Assume a residence time of 0.7 sec.

  Identify the risk factors

Conduct either a qualitative or quantitative risk assessment on this project. Identify the risk factors that you consider most important for the suspension bridge construction. How would you assess the riskiness of the project? Why?

  Determine the horizontal spacing of the vertical drain

determine the horizontal spacing of the vertical drains if the drains are installed in triangular grid to reach 90% of primary consolidation in 1.5 years after the commencement of fill placement

  Determine the depth of flow at the transition at a depth

A 1.6-m wide rectangular channel carries 1.8 m3/s at a depth of 0.85 m. The channel undergoes a smooth transition in which the channel bottom rises 15 cm and contracts to a width of 1.3 m. Assuming friction losses are negligible, determine the dep..

  Determine the horsepower dissipated in the jump

water flows at a velocity of 25 ft/s at a depth in a rectangular channel 16 feet wide. Determine the downstream depth necessary to form a hydraulic jump, the head loss through the jump and the horsepower dissipated in the jump.

  Calculate maximum allowable shear force v max for the girder

is fabricated of two 300 mm X 25 mm flange plates and a 800 mm X 16 mm web plate. the plates are joined by four fillet welds that run continuously for the length of the girder. each weld has an allowable load in shear of 920 kN/m.

  What is the maximum safe speed around the curve

What is the maximum safe speed around the curve? If the speed limit on the roadway is 60mph, what action should be taken by the engineer?

  Calculating the force in a punch press

Calculate the force (in Kn) a punch press must exert if it is to punch out a large washer from a strip of 5-mm thick sheet steel with an ultimate shear strength of 400 MPa.

  Determine what angle of twist

a beryllium copper wire having diameter of 1-50 mm and length of 40mm is used as a small torsion bar in an instrument. determine what angle of twist would result in the wire when it is stressed to 250 mpa.

  What maximum load can be applied tot the center of the beam

A simply supported steel 'I beam' is made of three 1"*8" plates with a mass of 898.4 lbmass each as shown in I beam form. Steel has a modulus of elasticity of 30*10^6 psi. The beam is allowed to deflect 1.05 inch.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd