User Account

All Pages

Determine the von mises distribution in the plate

Assignment Help Other Engineering
Reference no: EM13906162

1) For the truss shown in Fig. 1, determine the nodal displacements and stresses in each element by using hand calculations. Let the cross-sectional area of each element, A = 6 x 10-4 m2, Elastic modulus, E = 70x109 N/m2, Poisson's ratio, v = 0.3. You can solve the matrix equation by using a calculator or computer. Verify your result by comparing against ANSYS solution.

560_Determine the nodal displacements and stresses.png

2) A square simply supported 50 cm by 50 cm steel plate with thickness 3 mm has a round hole of 10 cm diameter drilled through center. The plate is uniformly loaded from the bottom surface with a pressure load of 15 kN/m2. Elastic modulus is E = 210 x 109 N/m2 and Poisson's ratio is v = 0.33. Determine the von Mises distribution in the plate.

1921_Determine the nodal displacements and stresses1.png

Reference no: EM13906162

Questions Cloud

Case study - faster flying- just add two more engine : Case Study - Faster Flying- Just add two more engine. Introduction and summary of case study and Identify the problem with Heading
What is ardens deductible loss from the sale of the shares : Arden purchased 300 shares of AMC common stock several years ago for $1,500. What is Arden's deductible loss from the sale of the 300 shares of AMC common stock?
What is christinas deductible loss on the sale of shares : What is Christina's deductible loss on the sale of 50 shares? What is her basis in the 50 new shares? Assume the same facts, except that Christina
A normally consolidated clay soil in the field : A normally consolidated clay soil in the field has a compression index of .25. The initial void ratio, was .6 with stress 3000 lb/ft^2. a) Find the void ratio if the stress is increased to 4500 lb/ft^2. b) find the primary consolidation settlement if..
Determine the von mises distribution in the plate : The plate is uniformly loaded from the bottom surface with a pressure load of 15 kN/m2. Elastic modulus is E = 210 x 109 N/m2 and Poisson's ratio is v = 0.33. Determine the von Mises distribution in the plate.
Previously used the equipment in his sole proprietorship : Liz and John formed the equal LJ Partnership on January 1 of the current year. John had previously used the equipment in his sole proprietorship. Are there any differences between inside and outside basis? Explain.
Calculate the ultimate primary consolidation settlement : A 30ft thick clay layer with doudble drainage settles 3 inches, in a time period of 2 years. The clay has a coefficient of consolidation of .000791 in^2/sec. a) Calculate the ultimate primary consolidation settlement. b) how long will it take to sett..
Use rounded amount in subsequent computations : Nancy, the owner of a very successful hotel chain in the Southeast, is exploring the possibility of expanding the chain into a city in the Northeast. She incurs $28,500 of expenses associated with this investigation. Determine the amount that Nancy c..
Discuss four ways self- efficacy can be increased : Explain why strong "Self-Efficacy" combined with "Goal Setting" can positively impact performance. Then identify and discuss four (4) ways "Self- Efficacy" can be increased

Reviews

Write a Review

Other Engineering Questions & Answers

  Traction force between the tires and the road

A car uses 25 hp to drive at a horizontal level at constant 100 km/h. What is the traction force between the tires and the road?

  Problem regarding the downward force

If the pressure inside is 1.0 atm, what downward force must the crew exert on the hatch to open it?

  Why the bernoulli process assumptions might not hold here

What is the largest value of n so that P(Y > 0) = 0.02 and briefly explain why the Bernoulli process assumptions might not hold here.

  Determine the work done by the butane during the process

Show that it is reasonable to assume that butane behaves as an ideal gas during this process. Determine the work done by the butane during the process.

  Justify a need for digital forensics methodology

Justify a need for digital forensics methodology and consider scope of the case including nature of alleged misconduct leading to consideration of how electronic and digital evidence may support the investigation.

  Calculate the marginal cost and the marginal revenue

Calculate the marginal cost and the marginal revenue for the product x2. Hint) Use the coefficients of x2 in constraints and dual prices and Formulate this problem as a linear program.

  Appropriate symbols from tables

Draw a process-flow diagram of the separation process using appropriate symbols from Tables. Include the gas compressors and heat exchangers. Label the diagram with all of the data given above, and number all process streams.

  Determine the largest intensity w of the distributed

If L = 18ft, beam will fail when the maximum shear force is V max = 800lb or the maximum moment is M max = 1200 lb · ft. Determine the largest intensity w of the distributed loading it will support.

  Describe how security administration works to plan

Describe how security administration works to plan, design, implement, and monitor man organization's security plan.

  What control signals does the microcontroller send out when

8. a in the normal expanded wide mode or the normal expanded narrow mode the mc9s12dp256b microcontroller can fetch

  Velocities at the inlet and the exit

Water enters a pump steadily at 100 kPa at a rate of 35 L/s and leaves at 800 kPa. The flow velocities at the inlet and the exit are the same, but the pump exit where the discharge pressure is measured is 6.1 m above the inlet section. The minimum..

  Plot the bod remaining in the water

CEE 357 Winter 2014, HW#5, How much HOCl is needed to react with each mg/L of S in the latter reaction? Plot the BOD remaining in the water

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd