Determine the velocity and acceleration of point c of belt

Assignment Help Civil Engineering
Reference no: EM13210755

The rated speed of drum B of a belt sander is 2400 rpm. When the power is turned off it is observed that the sander coasts from its rated speed to rest in 10 s. Assuming uniformly decelerated motion, determine the velocity and acceleration of point C of the belt, (a) immediately before the power is turned off. (b) 9 s later.

Reference no: EM13210755

Questions Cloud

Determine the compound empirical and molecular formula : A Silane contains 90.31 % silicon and 9.69 % hydrogen by mass. The compound has a molar mass of 62 g/mol. Determine the compound's empirical and molecular formula.
Depict the structures including hydrogen atoms : Dehydration of 2-methyl-2-pentanol forms one major and one minor organic product. Draw the structures, including hydrogen atoms,
Determine the horsepower of the device : water flows from a lake as is shown in fig. p8.40 at a rate of 4.0 cfs. is the device inside the building a pump or a turbine? Explain and determine the horsepower of the device. neglect all minor losses and assume the friction factor is .025
Draw a small sketch that shows a situation : Name three types of metamorphic foliations, and draw a small sketch that shows a situation where a metamorphic foliation could cause problems in an excavation.
Determine the velocity and acceleration of point c of belt : determine the velocity and acceleration of point C of the belt, (a) immediately before the power is turned off. (b) 9 s later.
Explain what is the emperical formula of the compound : An organic compound X contains C, H, and O. A 16.69 g sample of X underwent combustion analysis, leading to the production of 44.71 g CO2 and 10.99 g H2O. What is the emperical formula of the compound?
What will be the new level of service : If an additional 11ft lane is added (each direction) and all other factors stay the same, what will be the new level of service?
Explain why thomas jefferson encouraged western expansion : Explain why Thomas Jefferson encouraged Western expansion. Explain the repercussion of Wester expansion after the 1800
Determine the cycle time for a single engine scraper : Determine the cycle time for a single engine scraper rated at 21 cy heaped that is used to haul material from a pit to a fill 900 ft away under severe conditions.

Reviews

Write a Review

Civil Engineering Questions & Answers

  What is the total bod loading per day

The factory will use a 4 ft deep on-site lagoon to stabilize the waste with a loading rate of 20 lb BOD/acre-day. Part a) What is the total BOD loading per day?

  List five soil and water management strategies

List five soil and water management strategies appropriate for agricultural use of ultisols. 100-150 word limit.

  Quartzite sample in a compression testing machine

A quartzite sample in a compression testing machine is 180mm long and 54mm in diameter. what is the stress under a load of 100kN? if the modulus of elasticity is 102kN/mm2, find the strain develope in the sample.

  Length of the curve-elevation of the curve at station

A vertical curve is to connect two tangents that intersect at station 50+00 and the elevation 500.00ft. The back tangent gradient is -4 percent, the forward tangent gradient is 2 percent, and the elevation of the curve at station 48+50 must equal ..

  What length l of splice plate is needed

two strips of a plastics material are bonded together as shown. The average shearing stress in the glue must be limited to 1000 kpa. what length L of splice plate is needed if the axial load carried by the joint is 55 kN and the width (W) is 315 m..

  Sulphate ions in natural and industrial environments

List some of the common sources of sulphate ions in natural and industrial environments. For a given sulfate concentration, explain which of the following solutions would be the most deleterious and which would be the least deleterious to a permea..

  Determine the mass ratio

Determine the mass ratio, For a vehicle in gravitationless space, determine the mass ratio necessary to boost the vehicle velocity by 1600 m/sec

  Draw the shear diagram for the shaft

Draw the shear diagram for the shaft. The bearings at and exert only vertical reactions on the shaft

  What is the maximum height

The height (in meters) of a projectile shot vertically upward from a point 2 m above ground level with an initial velocity of 24.5 m/s is h2+24.5t-4.9t^2 after t seconds. a) When does the projectile reach its maximum height? b) What is the maximum..

  Use differentiation to find a general expression

(a) Use differentiation to find a general expression for the rocket's velocity as a function of time, (b) When is the velocity zero?

  Operational changes to prevent river from contamination

assuming that the contaminant travels mainly by advection, propose any operational changes to the given layout to prevent the river from being contaminated.

  Deriving the eom for building

Working a problem where there are two one-story buildings of different heights next to each other. Earthquake imparts a base motion z(t) that is a cosine function. I'm given a shape function for a column of height L when deriving the EOM for each ..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd